Jump to content

electrathon

Contributing Member
  • Content Count

    3,014
  • Joined

  • Last visited

4 Followers

About electrathon

  • Rank
    Instructor
  • Birthday 12/13/1962

Contact Methods

  • AIM
    arw62
  • ICQ
    0

Profile Information

  • Gender
    Male
  • Location
    Gresham, OR

LW Info

  • Leatherwork Specialty
    Floral

Recent Profile Visitors

28,604 profile views
  1. I agree with this. It sounds like raw, not boiled. If it is, it will remain sticky. Do your best to remove it.
  2. Contact Jason, he will likely let you buy it at the deal. He has been sending out updates as he gets more of the video work done. Very professional for a small scale video. His classes are great too if anyone is interested. His goal is simple shoemaking.
  3. Leather Wranglers is one of the best. Bob Beard is the other best choice, but he makes limited quantities and they are hard to get.
  4. Use this: https://www.amazon.com/SE-841DH-Micro-Double-Ended/dp/B000RB5JJO/ref=sr_1_8?ie=UTF8&qid=1522781654&sr=8-8&keywords=pin+vise cut in half and glued in. I find they hold better than the Starret ones that are 4 time more money.
  5. This is correct if the bottom sole and midsole are both damaged. If it is just the bottom sole it is a lot easier. If it is, you can carefully remove the bottom sole (there is a solvent) and then put on glue primer. Two layers of glue, then attach the sole. Trim off the excess with a belt sander and you are done. It is a lot more complicate if it is more than just the lower sole.
  6. It depends on the style of sole that is on the boot. If it is flat glues on sole you likely can do it. If it is a molded sole it is not going to happen. Weldwood in not strong enough to hold it, Renia, masters or barge.
  7. Go to Jason's website, the turn shoe DVD is available now. He produced it a couple years ago. The Boot DVD is the one he is currently making. His site is : laughingcrowe.com
  8. I also know Jason. The videos he is producing are top notch. If you are looking to make a simple set of boots I highly recommend this video.
  9. Yes, replace the motor with a 120volt single phase (this is the common one) servo motor. You will get better slow stitching with the swap too.
  10. I am curios to hear how your experiment is going with a laser cutter? please get back to me on this!

    1. Show previous comments  1 more
    2. OLDNSLOW

      OLDNSLOW

      did you get a K40 of some variation

    3. electrathon
    4. OLDNSLOW

      OLDNSLOW

      that is one of the variations of a k40 laser, there is a user group on google, if google k40 users group you find a lot of users there, I purchased the same know that I would be making upgrades to it, and still am working on some that renders a better machine.  Good luck with yours once you start working with it.

  11. The Bob Beard class is coming up very soon. If you are interested I can get a couple people into the class. Located in Portland Oregon, hosted at Oregon Leather. Contact me with any questions. Aaron
  12. The pattern is cut, it is stamped in with the tool. Then you bevel. The tool comes as a set.
  13. The guy is on facebook, the Pinterest image is of the tool. He makes a few different angles of the tool. I bought mine a couple years back and have not done any more than play a little with it. I just looked at the above link, that is the guy.
  14. Could be. But if you look very close he would have had to turn his knife exactly the same and made intentional overcuts at a completely different angle than he was cutting at. Almost impossible to do, on purpose or accident. The imperfections are all in a straight line, as are the other imperfections. It looks to me like he was not that used to using the mini5 tool and got a little off on the alignment as he moves across the leather.
  15. That looks like a mini5 basket stamp tool.
×
×
  • Create New...