Jump to content

Recommended Posts

hello, this will be my first post.

I just got a Landis 3 and I am looking for any help possible.

I have found parts of the manual but they are no help at all.

pictures or videos would be great.

thank you .

Share this post


Link to post
Share on other sites

Hi gregoire, glad to have you join us! :welcome:

I don't have this particular machine, but I'm pretty sure there are at least a few people here who do and can help you. I think that will make it a little easier for someone to help you if you could be a little more specific about what you're trying to do, and what kind of problem you're running into.

Kate

Share this post


Link to post
Share on other sites

Hi gregoire, glad to have you join us! :welcome:

I don't have this particular machine, but I'm pretty sure there are at least a few people here who do and can help you. I think that will make it a little easier for someone to help you if you could be a little more specific about what you're trying to do, and what kind of problem you're running into.

Kate

Kate,

Thank you! I basically would need all the info I could get. From the set up, making sure I am threading the machine properly, to help adjusting tention to get a proper stitch.

I have the machine set up and have tried to stitch some leather but the loops on the bottom are not getting tight and are getting stuck on the bobbin.

I will try to take a few picture and attach them to this post.

I am thinking of trying to hire someone locally (san Diego) to help me with the initial set up.

v/r

gregoire

Share this post


Link to post
Share on other sites

I would try the local shoe repair shop.

Ask them to teach you about the machine ( not shoe repair as they may not want to create a competitor) offer them some compensation for time and effort. The worst that can happen is they may say YES :)

Share this post


Link to post
Share on other sites

CampbellRandall has some videos on Youtube I think, and the machines are pretty much alike, if you can run one, you can run the other.

Good luck,

Kevin

Share this post


Link to post
Share on other sites

all,

Thank you for your help

here are some pictures, I hope it helps

post-20926-084161100 1304571109_thumb.jp

post-20926-012142600 1304571172_thumb.jp

post-20926-055768900 1304571243_thumb.jp

post-20926-005577100 1304571272_thumb.jp

post-20926-007988100 1304571291_thumb.jp

post-20926-019407700 1304571316_thumb.jp

v/r

Gregoire

Share this post


Link to post
Share on other sites

Still no luck!

Any help would be great!

thank you

Try threading the top thread under the first take-up roll and over the second. You have it over the first, therefore the machine will not pull enough thread, leaving the large loops.

Share this post


Link to post
Share on other sites

Try threading the top thread under the first take-up roll and over the second. You have it over the first, therefore the machine will not pull enough thread, leaving the large loops.

Thank you. i did correct that a few days ago.

It is a little better but I still have long loops in the bottom of the leather.

Share this post


Link to post
Share on other sites

I am still working for some help. I am stil unable to make a propers stitch. Anyone in California, Arizona who could help me?

Share this post


Link to post
Share on other sites

I know absolutely nothing about your particular machine but, you need help so just maybe a different idea?

When I have had the problem you are having it is usually one of about three things.

No. 1 Your machine is not threaded correctly

No. 2 Your thread has slipped out of place on a sprocket/tensioner, might even down behind the mechanism.

No. 3 The tension on the machine is totally out of whack. I would start from ground "Zero" on both top and bottom tension (if the machine has both). Adjust the tension about 1/4 turn on both or leave the bottom alone and do this on top tensioner only. Sew a few stitches, check to see what is happening, another 1/4 turn, sew, check.

I became so disgusted when I couldn't get my machine to sew correctly that I finally just took the tensioners to zero and started all over. After fussing and fuming several times I hit the right spot.

Wiz has taught me a lot about my machine and others. If I never learn anything else about the Consew I have, there is a "SWEET SPOT" when you hit that you need to do very little adjusting on most thicknesses of leather or layers of leather.

ferg

I am still working for some help. I am stil unable to make a propers stitch. Anyone in California, Arizona who could help me?

Share this post


Link to post
Share on other sites

I can't really tell by your pictures what the problem is, but Campbell-Randall is right about the first take up roller needs to be threaded on the underside. There is no thread tension plates on a Landis 3. It looks like maybe your needle may not be releasing your top thread as the shuttle passes through the loop. It could be pulling the thread on down and breaking or cutting the thread. Could be the thread locks on the top side are wore out and are not locking the thread to keep it from pulling on down to the bottom side. The shuttle tension could be to tight and holding the thread down. You can loosen the shuttle tension by turning the small screw on the side of the shuttle. Turn it counterclock wise a small bit at a time, carefully! Just a small amount of turn and then try a stitch or two to see if it is helping. Also the bobbin MUST be threaded in straight layers to function properly. Also some machines have a little trouble with the last 1/3 of the thread on the bobbin. Get you a book for the 3 and read all of it and it will help you immensely. Also Campbell-Randall handles some parts for your machine and if you will call them they can talk you through this a lot better than me! I personally have a Landis #1, Landis #3, and a Landis #16, and they are all great old machines. Some parts can be a real problem, and it helps to have a machinist friend! LOL But if you get the old machine going you will be surprised at the pretty stitch it will make, and no threaded needle machine can compare onthick leather items!

Share this post


Link to post
Share on other sites

Thank you all. First problem is my bobbin is not threaded properly. It s not properly done in straight layers.

I did find a book but it has part numbers and treading sequence by part numbers. might as well be in chinese. I will work on it in the next couple days and take better pictures.

Again thank you to all for your help!

v/r

Share this post


Link to post
Share on other sites

BTW, if anyone has video or books that could help me get this going I would love to buy/borrow/trade anything.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Create New...