Jump to content
StrigaMort

Adding Weight To Poly Mallet?

Recommended Posts

Hi everyone, first post. Very happy to be here.

So I have a basic set of tools. I am starting out making knife sheaths and am really enjoying it. My problem is that for basket stamping, my small poly mallet is sorely lacking. I don't have the funds at the moment to buy the BK maul that I really want, but like the idea of adding some weight. I'm pretty handy, and think I might get away with simply drilling some holes and adding steel shot (or similar),just wondering if anyone has done anything like this.

Does it upset what little balance there is in this puny whacker?

Thanks for any insight.

Share this post


Link to post
Share on other sites

Hi,

I am a newbee and am faced with the same situation. I have some lead flashing laying around the basement and have been considering wrapping it around the poly head and securing it to the handle. Maybe a little rubber cement to keep it from shifting. This may be a stupid idea and have not tried it yet but it's the best I have to offer at this time. I hope someone smarter than me can offer a better suggestion to you.

Good Luck!

Share this post


Link to post
Share on other sites

Harbor Freight has some inexpensive dead blow mallets. +- $6 with discount.

I will often use one when my expensive Stohlman is being used by my assistant.. I also have a larger dead blow for other tasks like punched and cutters.

Cya!

Bob

Share this post


Link to post
Share on other sites

If you want to modify your mallet you can always drill a large hole fill it with lead shot and use some type of epoxy to seal it all in. But in all actuality getting a dead be from HF would be cheaper

Share this post


Link to post
Share on other sites

Hi ya all

I would love something heavier too. I borrowed a dead blow mallet from a leatherworking friend but I found it way to bouncy and not ballanced properly at all for my needs. Just thought I would toss in my experience with one as I wait for the day I too can afford a nice heavy mallet or maul.

Cheers, Toolingaround

Share this post


Link to post
Share on other sites

Sure you can add weight. Just drill some good pilot holes and put as many woodscrews as you want in there. Would probably be a good idea to do it in sets and try to keep the mallet balanced. Strips of lead secured to the head should work fine also.

Share this post


Link to post
Share on other sites

Thanks guys, I'll let you know how it works out. :)

Share this post


Link to post
Share on other sites

http://woodworker.com/16-oz-wooden-carving-mallet-mssu-128-087.asp?search=mallet&searchmode=2

You can always try one of these. Price is reasonable

Edited by glockanator

Share this post


Link to post
Share on other sites

Seems like that would get dinged up pretty quickly. Wood chisels don't have the tiny surface area of a leather stamp, and I don't think you usually hit as hard. If I didn't need a bunch of other stuff I'd just buy the $50 BK. Rats.

Share this post


Link to post
Share on other sites

I would say just get the small BK Maul from Springfield

Share this post


Link to post
Share on other sites

I would say just get the small BK Maul from Springfield

For crying out loud ! Wake up ! He said .........he doesn't have the funds to buy one,

Share this post


Link to post
Share on other sites

You know, on second thought, forget about adding lead strips. Bare lead is not a good thing to have in your shop.

What you might do, is get some fully jacketed bullets, and drill just slightly underside holes is the mallet head, and then pound the bullets in. Like with the screws, space the bullets to keep mallet balanced.

Share this post


Link to post
Share on other sites

For crying out loud ! Wake up ! He said .........he doesn't have the funds to buy one,

I know what the OP said and I dont think your comment was called for

I tried adding weight to a mallet and it dont work very well thus the reason for my comment

Like I should have to write an explaination for my comment in the first place

Share this post


Link to post
Share on other sites

I know what the OP said and I dont think your comment was called for

I tried adding weight to a mallet and it dont work very well thus the reason for my comment

Like I should have to write an explaination for my comment in the first place

LOL Your signature quote is pretty ironic. Yes my comment was called for. If I am following a thread, and there is a new entry, then I have to take the time to open the email notification and check it out. In this case, it was a total waste of my time to read your suggestion that the OP do something he already said wasn't in the picture.

Share this post


Link to post
Share on other sites

Guys, seriously?

St8,it would have been more complete if you had mentioned that you had tried modifying a mallet in your first post, but it doesn't really matter to me that you didn't.

For the record, everyone's comments, recommendations, opinions and experiences are welcome in my threads regardless of whether or not others find them beneficial. I've never understood why people get upset about another person's post in a DISCUSSION forum. Say what you please, or don't.

WS, I appreciate your input. Really,I can clearly see that you are helpful in a lot of threads that I've looked at. I cannot imagine, however,how you get by if a post like the above bothers you.

Golden rule and all that. I also tend to try and think of how I'd say something were the other person standing in front of me. It's worked pretty well for more years than I care to admit. ;)

Again,thanks for all comments in any of my threads.

I picked up a 1.5lb dead blow yesterday from Harbor Freight Obviously it won't be optimal (otherwise everyone would be using them), but it feels pretty good. Certainly better than the small poly. I nearly bought a kit of wheel weights, but I think it would have been a waste of time. I hate not knowing what I'm missing, but in this case, I guess I'm happy because I'm not seeing an eminent downside to this $6 pig. Guess I'll have to shell out a few bucks one day to find out, but for now I'm happy. I think. :)

Edited by StrigaMort

Share this post


Link to post
Share on other sites

Standard+Head+Dead+Blow+Hammers+-+21+oz+

Posts crossed...

Edited by BDAZ

Share this post


Link to post
Share on other sites

Striga mort

just trying to keep you from postponing the inevitable cause once you try one of the little one pound mauls it will be all over at that point :spoton:

but seriously a maul will give you the most consistancy in your stamping not only with the depth of the impression but the placement accuracy is increased with less stress on the hand.

so ya although pricey buying a maul will be a beneficial addition to your leatherworking tool collection

Share this post


Link to post
Share on other sites

If your going to be using stamping like a basket weave i would get a 24 ounce a 16 ounce is to light for stamping. A 16 ounce is fine for tooling though.

Share this post


Link to post
Share on other sites

I am partal to the one pounder, the two pounder wears my arm out.

Share this post


Link to post
Share on other sites

I am partal to the one pounder, the two pounder wears my arm out.

Well it's a good thing I'm strong like bull. :P

Seriously though, when I picked up the 1.5lb dead blow it felt heavy enough that I was surprised that anyone used this weight, or even heavier. Now that I've used it, I can see why. I tried a little back to back with the poly mallet. The Tandy whacker felt terrible after using the DB. It felt really bouncy and way waaay too light. I was using the basket stamp. I guess I could see using it with a seeder or something else that cuts deep, but for heavier stamping I think the 1.5lb will be the minimum.

Even if I never use the DB again after buying the BK maul, it'll have been worth the $5 just for the experience in weight.

Share this post


Link to post
Share on other sites

Your impressions will be a lot deeper and crisper with the heavier one to and with a lot less effort.

Share this post


Link to post
Share on other sites

The HFDB mallet is very useful for punches and snaps setting as well. I use it when I don't want to ding my good maul. The heavy HFDB hammer is great for heavy tasks like whacking the arbor press or using large punches. on heavy leather.

Cya!

Bob

Share this post


Link to post
Share on other sites

Striga Mort

as BDAZ said the dead blow hammer will still have its place in your leather shop for setting snaps and other hardware

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Create New...