Jump to content
gtwister09

Neat Trick for Needle Sizing

Recommended Posts

When visiting a home sewing machine shop, I watched the following tip. I thought how clever it would be for people having issues with the wrong needle thread sizing. I know that many of us have charts but this is a quick and dirty method.

This lady carted in with a machine, a cigar box FULL of needles, about 10-12 spools of thread, some light fabric, some heavy denim and some suede (4-5 oz). Turned out that this machine was given to her by her Mom and that she had seen her sew all these materials on it with no issue. She was constantly breaking threads and thought that the machine was the issue so this guy had already cleaned, oiled and tuned it up for her. However she still had issues so he was going to help her set up needles and thread to match materials.

First thing they did was look at about 20 needles from the cigar box and throw some of them away due to burrs. He told her that she would have to go through the rest of the box but showed her how to do that.

Next they selected one of the threads for the leather and started to select a leather needle. He picked out a diamond shaped one and told her to cut 3 foot of thread. He then "tested" it and said that this one will create issues. He picked another one and said this combination of thread and needle will work. He did it for 3 other pieces of thread and finally came up with some combinations that would work. Then he tried it on her machine andn it worked perfectly with her sewing without any issues.

Correct Thread - Needle Sizing Tip

(1) Cut about 3 feet of thread that you are going to use

(2) Select the needle that you are going to use

(3) Thread the needle on one end and leave about 8 inches past the end of the needle (If the needle sticks at this point it is too small)

(4) Hold the needle in one hand (thumb and forefinger) and wrap the excess thread around the forefinger

(5) Take the opposite end of the thread in your other hand and drop it down so that it makes approximately a 45 degree angle

(6) Make sure that the thread is tight between your two hands

(7) Release the needle from your thumb and forefinger and watch the motion that occurs

If the needle sticks at the top, it is too small - try the next largest needle.

If the needle is jerky as it slides, it is too small - try the next largest needle.

If the needles slides rapidly, it is too large - try the next smallest needle

If the needle slides steadily & evenly, it is the correct size.

Here's a chart from Excel.

Thread-Needle.jpg

Regards,

Ben

post-5-125621874658_thumb.jpg

Share this post


Link to post
Share on other sites

Thanks for the tip. The information you give just before the chart looks correct but the chart is incorrect and should be deleted or corrected to avoid confusion.

Share this post


Link to post
Share on other sites

Pic fixed. Good info, Ben, thanks!

~J

Share this post


Link to post
Share on other sites

Thanks! This is information I can really use.

Share this post


Link to post
Share on other sites

i was taught this method by master motor trimmers and passed it on when I was teaching. Great quick reference.

Share this post


Link to post
Share on other sites

It may work to tell you that a needle will work, but not that a needle won't work.  There are many needle thread combos that work, well actually that don't work, and the eye size is only one factor.  What I do is basically just follow the rules, and test combinations. 

In one of the type of sewing I do, outdoor gear, there are lot of people who want to get the strongest thread through the smallest hole.  Not a great approach, the needle bends, and the point strikes something and the process fouls up.  Any reason they had for doing it is no longer valid because the material is all snarled up.  This happens with leather also.  Either people want to run machines and therefore smaller needles than they should because it is all that they have.  or they want to minimize the size of holes in the work.  Just sticking to the normal set up is usually the best solution.

 

Jeans are an interesting example, size 16 needles and fat thread for top stitching, works great in denim.  But with leather the needle is the tool that applies tension, and there is often more than it can take required to close a seam.

Share this post


Link to post
Share on other sites

You mentioned needle charts in your first post.  Does anyone happen to have one that you would't mind reposting?

Share this post


Link to post
Share on other sites
3 hours ago, Bru said:

You mentioned needle charts in your first post.  Does anyone happen to have one that you would't mind reposting?

Here is a needle and thread size chart from Toledo Industrial Sewing Machines. It shows the best needles to use with thread size 33 through 554. It includes the diameter of the bonded thread, tensile strength, plies, Govt equivalent sizes and Tex size equivalents.

Share this post


Link to post
Share on other sites

Thanks Wiz - this is perfect!

18 minutes ago, Wizcrafts said:

Here is a needle and thread size chart from Toledo Industrial Sewing Machines. It shows the best needles to use with thread size 33 through 554. It includes the diameter of the bonded thread, tensile strength, plies, Govt equivalent sizes and Tex size equivalents.

 

Share this post


Link to post
Share on other sites
On 3/29/2016 at 1:23 AM, Massive said:

It may work to tell you that a needle will work, but not that a needle won't work.  There are many needle thread combos that work, well actually that don't work, and the eye size is only one factor.  What I do is basically just follow the rules, and test combinations. 

In one of the type of sewing I do, outdoor gear, there are lot of people who want to get the strongest thread through the smallest hole.  Not a great approach, the needle bends, and the point strikes something and the process fouls up.  Any reason they had for doing it is no longer valid because the material is all snarled up.  This happens with leather also.  Either people want to run machines and therefore smaller needles than they should because it is all that they have.  or they want to minimize the size of holes in the work.  Just sticking to the normal set up is usually the best solution.

 

Jeans are an interesting example, size 16 needles and fat thread for top stitching, works great in denim.  But with leather the needle is the tool that applies tension, and there is often more than it can take required to close a seam.

You are so right... in 45 yrs of sewing ...I can't agree more.

 

Share this post


Link to post
Share on other sites

Yes the old slide test is a good one, used to be in all the Singer operator manuals.   I also find that if when you go to thread your needle if its hard to get the thread thru its too thick, or if it just flops straight thru without seemingly even touching the side of the needle hole then its too thin..   There are times when you might want on oversize needle to thread relationship though, like sewing thick leather or sticky vinyl where you need the hole a bit bigger to give the the machine a chance to lock the stitch.....

Share this post


Link to post
Share on other sites

I'm hoping to get a sewing machine in the next month or so(I hope I can get the CB3200).  I have been hand sewing till now using basically just a few thread sizes I got from the local Tandy.  I see the chart Wiz had which I've copied.  Is there any reference or guide to go by on what thread to use for the project?  How do I determine what to use for say, a Holster? knife sheath? a Binder cover? I will be doing small/thinner and up to 3/8 thick items,  Mostly I will be using veg tanned.   Using the search tool here hasn't told me much yet, but I haven't stopped looking.  I want to be able to get a small selection of needles and thread when I am able to get a machine and have some guide on what needle or thread to use. 

Any direction you can point me in to look, will be appreciated.

On ‎7‎/‎14‎/‎2016 at 7:03 PM, Singermania said:

Yes the old slide test is a good one, used to be in all the Singer operator manuals.   I also find that if when you go to thread your needle if its hard to get the thread thru its too thick, or if it just flops straight thru without seemingly even touching the side of the needle hole then its too thin..   There are times when you might want on oversize needle to thread relationship though, like sewing thick leather or sticky vinyl where you need the hole a bit bigger to give the the machine a chance to lock the stitch.....

This made ALOT of sense. Now just which needle/s for what thickness of leather?

Share this post


Link to post
Share on other sites

Most people use #277 on sheaths & #138 on the thinner leather.

Share this post


Link to post
Share on other sites

Thank you Bob! this helps.  I hope to order in the next month.

Share this post


Link to post
Share on other sites

I use the strongest thread size with which I can hide the knots inside the material. This equates to the following general purpose outline. The thicknesses are not fixed in stone. You may want to use a thicker thread on top and thinner thread on the bottom, for a bolder topstitch appearance. Or, you may decide to groove out a stitch line and fill it with smaller top thread that lies below the surface. The strength of each mixed size stitch is decided by the smaller size thread.

  1. #69 thread into about 3-4 ounces (~11 pounds test)
  2. #92 thread into 5-7 ounces (~15 pounds test)
  3. #138 thread into 8-11 ounces (22 pounds test)
  4. #207 thread into 12-15 ounces (32 pounds test)
  5. #277 into 16-32 ounces (45 pounds test)
  6. #346 into 33-64 ounces (53 pounds test)
  7. #415 into over 3/4 inch (72 pounds test)

Share this post


Link to post
Share on other sites

Thank you Wiz.  saving this in a file!

Needles?   Would I use needles that the thread fits as described by Singermania typically?

I do appreciate the help.

Share this post


Link to post
Share on other sites
7 hours ago, Sticks said:

Can someone tell me the best needle for the Seiko STW-8B ?

The person I bought the machine from told me to use 17/231 needles.

However google told me 135/17 or 16 for leather.

Im a bit bit confused . Ill be mainly using bonded nylon 40s (#69).

Also I only seem to be able to find 16/231 not 17.

thnx

Needle System 135x17 (round) or 135x16 (leather)

Share this post


Link to post
Share on other sites

I have a query regarding the general guidelines for working with specific weight yarns on needles.
I have a gauge for the needle size that also indicates the proper weight of yarn to use with those needles. What if you had larger or smaller needles, I wonder? For instance, I have a pattern that calls for size 8 needles, but my light-weight yarn suggests using a size 5 or 6. If I use heavier needles and lighter yarn, how will it affect the stitch? What if I used smaller needles and thicker weight yarn instead?

Share this post


Link to post
Share on other sites
9 hours ago, Hali said:

I have a query regarding the general guidelines for working with specific weight yarns on needles.
I have a gauge for the needle size that also indicates the proper weight of yarn to use with those needles. What if you had larger or smaller needles, I wonder? For instance, I have a pattern that calls for size 8 needles, but my light-weight yarn suggests using a size 5 or 6. If I use heavier needles and lighter yarn, how will it affect the stitch? What if I used smaller needles and thicker weight yarn instead?

When you say "yarn" do you mean the fluffy soft stuff, or smooth thread? Your use of "yarn" suggests that you are not into industrial leather sewing machines (yet). We usually deal with "thread" that is bonded together and lubricated to withstand the friction and heat generated when sewing leather. I think of yarn as something one would use in a sweater. Further, most of our needles start at a #16 or 18 and go UP from there. I don't even possess a #8 needle for my one straight stitch machine.

What make and model sewing machine are you using that uses a #8 needle? What is the brand of the "yarn" you want to use? A small photo of the bottom of a spool would help. Take the photo at as small a resolution as possible to be within our upload limits.

As a guideline, no matter what type of thread you want to use, it must slide through the eye of the needle. If you also have a bobbin in the machine, the needle must poke a big enough hole to pull up two threads that overlap into a knot. So, if a needle is already tight when you test it with just one thread, it probably will be too small to pull up both threads and their knots.It also depends on the density and thickness of the sewn material. It is easier to pull up knots in soft linings and broad cloth than in nylon, denim, vinyl and leather. Just use a bigger needle if you see knots on the bottom despite making tension adjustments!

Share this post


Link to post
Share on other sites
11 hours ago, Wizcrafts said:

When you say "yarn" do you mean the fluffy soft stuff, or smooth thread? Your use of "yarn" suggests that you are not into industrial leather sewing machines (yet). We usually deal with "thread" that is bonded together and lubricated to withstand the friction and heat generated when sewing leather. I think of yarn as something one would use in a sweater. Further, most of our needles start at a #16 or 18 and go UP from there. I don't even possess a #8 needle for my one straight stitch machine.

What make and model sewing machine are you using that uses a #8 needle? What is the brand of the "yarn" you want to use? A small photo of the bottom of a spool would help. Take the photo at as small a resolution as possible to be within our upload limits.

As a guideline, no matter what type of thread you want to use, it must slide through the eye of the needle. If you also have a bobbin in the machine, the needle must poke a big enough hole to pull up two threads that overlap into a knot. So, if a needle is already tight when you test it with just one thread, it probably will be too small to pull up both threads and their knots.It also depends on the density and thickness of the sewn material. It is easier to pull up knots in soft linings and broad cloth than in nylon, denim, vinyl and leather. Just use a bigger needle if you see knots on the bottom despite making tension adjustments!

Got it, got it.. Thankyou so very much !

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Create New...