Jump to content

JLSleather

Contributing Member
  • Content Count

    7,353
  • Joined

About JLSleather

  • Rank
    Leatherworker.net Regular

Contact Methods

  • Website URL
    http://jlsleather.com

Profile Information

  • Gender
    Male
  • Interests
    My babies, leathercraft, fishin'

LW Info

  • Leatherwork Specialty
    carving
  • Interested in learning about
    suppliers
  • How did you find leatherworker.net?
    search engine

Recent Profile Visitors

39,598 profile views
  1. I generally and usually and normally and routinely and consistently (and prolly some other ly's) advise NOT to use ant-streak on leather. But on "figure carving" I DEFINITELY WARN against it. Just don't belong on 'figures' at all. That said, I think you could benefit greatly from seeing Stohlman's book on figure carving, specifically look at 'matting" and double beveling. Still, your knife cuts look good n smooth Maybe this helps? Figures here also from "craftaid" templates.
  2. yeah, prolly work there, long as the land is wide enough. Mostly on chrome-tanned bags, I would think. Assuming we're talking about the same type of bag, a 90° on a veg-tanned edge would likely cause a "booger" (wrinkle) I would find unacceptable. Still, it may be of use for like gussets on notebooks/binders?
  3. One is a six, the other seem more like half a dozen. I've had customers ask, and I tell 'em by the time either wears out, send it back and I'll replace the stitchin' in it - you just pay the shippin'. They DO sew a bit different, barely, if I'm tellin' the story. EITHER is fine - but you might notice when switching from one to the other you might adjust the tension just a tad, even with the same weight of thread. Again, I have and use both, so ... Originally, I used nylon for no other reason than that's what I had on hand. I "tried" poly thread because it was available in a color I wanted and the nylon was not, at least with my regular supply stores. The difference in use is minimal... almost none .. and I dont know there's much difference in the wear of it either. Somebody said that somebody said poly might be a bit more UV-resistant... but that same 'they' also tell you that tooled leather needs ant-streak and theyz WMD in Iraq ...
  4. I didn't find I use the "holster" or "stirrup" plates nearly as much as I thought I would. With just a little thought, the standard plate does prett much all of that. I suppose if you were trying to sew next to a metal clip....
  5. Correct. I've got a few decent pieces from there, but they were the exception. I would call and complain, they would apologize for the "mistake", send me a different piece. But I was spending SO much time on the phone with them, it just became not worth it. They didn't seem to understand that I KNOW what H.O. A and B grade looks like - usually that's what I would order and use SLC for the ocassional odd weight. Like as in I don't use a lot of 5/6, so instead of buying multiple sides from H.O., I would order 7/8 at H.O. and use SLC for the ocassional 5/6 or 4/5. I got one side of 5/6 I could stretch a 1.5" wide strap by hand. ANYWAY.... Wickett/Craig has good leather, I've made a lot of holsters from their skirting leathers. That in mind, I have had a few issues with W/C as well, though not nearly as often. More than once I called to remind them that I don't mind PAYING premium as long as I'm GETTING premium. If you want to go with H.O. but don't want to buy minimum 10 sides, I always recommend Goliger Leather. It's a bit higher cost than some places, but they have ALWAYS sent me great leather. NEVER ONCE a piece I wasn't happy with. http://www.goligerleather.us/
  6. back to the original point, I dont do a LOT of basket stamp, but when I do, I leave the back side of the holster (wearer side) SMOOTH, UNSTAMPED. Nothing to do with lazy - I want a smooth surface to glue down the belt loop to.
  7. yup. LL is a diamond hole. I don't much like the "D" of "S" needles, as they make a hole I think is not as strong in teh direction of sewing, and I don't like the way it leaves "space" between stitches. EDIT TO ADD: I like a #24 needle, 277 thread on the "top" and 207 on the bottom MOST of the time (I have been known to sew 207/207). The pics above were #24 needles. yes, you certainly are. I found the service at LMC more hype than reality. I remember a post about it disappearing, prompting me to ask if advertisers here can get that done for them. Meh - perhaps it's better now, it's been a good while since I dealt with them.
  8. exactly what i use - LL point, #24 pics show close up of the difference in a couple styles. the LL and LR points are the SAME needle size, same thread size, and same stitch length. The LR is kinda lacy and girlie, doesn't pull as deep, and makes the stitch LOOK longer (it isnt) teh LL pulls in deep, results in a very straight and tight stitch, with a hole geometry unlikey to tear.
  9. Easy enough to put the spring steel between the outer leather and the liner - since this was all black it didnt' really matter one way or other, so this is done to show the construction.
  10. Yes, and yes. USUALLY, a 'regular' line 24 snap, a piece of spring steel and a rivet, give the thing some substance to push on. This one on the back of a 686 / Python holster. Busy again, but stil meaning to get back to this conversation. PM sent...
  11. I wouldn't antique a basket stamped leather anything. But then, I don't antique anything (save about twice where somebody threatened me with money if I would do that to the project, against my recommendation). If the moisture content of the leather is right, the burnish of the leather negates the need for ant-streak That said, IF a guy was insistent on that goop, considering that type of holster, I would then grudgingly recommend ... Cut out leather Stamp Line (if used) Sew Wet form Allow to dry completely. Oil if desired Ant-streak, using a fingertip TanKote or other top finish (I use resolene sometimes, sparingly)
  12. I like the thread from Superior. Big color selection (including hot pink). That said, i also like the 'cowboy' brand I bought from Bob K / Toledo Ind Sewing.
  13. It actually looks like we need to get you a good piece of cowhide. Using sub leather to learn the craft is like a guitar player trying to tune his ear with something off the walmart shelf How thick is that? I 'might' have a piece around here somewhere. Off to somewhere right now, but I'll check back.
  14. dude - it's the SAME MACHINE. If you're already dealing with Bob K / Toledo Ind Sewing, I highly recommend you stay with him.
  15. Tha's a LOT of work! Lookin' good
×
×
  • Create New...