Jump to content
coop

Basic Tooling Question

Recommended Posts

I am working on a strap for a friend and I was wondering what would be the best tools to use for this design? The strap will be black, the flame and design will be raised, the flames stay black and the letters will be antique gold. I want to just fade it into the strap instead of doing a border. I have a couple tools B701, B205, and A104. I'm sure that I can do it with what I have I was just looking for different opinions. Thanks

post-40151-0-97441200-1371836925_thumb.j

Share this post


Link to post
Share on other sites

do some test flames on scrap and see what you like best. Do a portion of it with no background, then a portion with each of the backgrounders you have. Other than that it's just beveling.

Share this post


Link to post
Share on other sites

I have the bevelers with the hatching on them, I'm thinking of getting the smooth ones for this design. The backgrounders I have a the pebble type, E294.

Share this post


Link to post
Share on other sites

The backgrounders I have a the pebble type, E294.

You also have that A104 ;), but I'm not a big fan of those either.

Get yourself some Barry King bevelers since you're buying some new ones anyway. You'll want them for the detail in those flames.

Share this post


Link to post
Share on other sites

You also have that A104 ;), but I'm not a big fan of those either.

Get yourself some Barry King bevelers since you're buying some new ones anyway. You'll want them for the detail in those flames.

I'll pick some up this eve. Going to be next week before I can get back to it anyway. Thanks!!

Share this post


Link to post
Share on other sites

Are you sure you want to dye the flames black? I think they will be hard to see if the strap is black. Nice design!

Share this post


Link to post
Share on other sites

I had thought about coloring them but I am using Angelus Scarlet Red for the D and Antique Gold for the T. I didn't want to take away from the logo, (which is a band logo) and have the flames appear as you got closer to it. If I did the flames in red it would wash the D and then I would have to tie the logo and flames together and that seems too busy. Does that make sense? I'm open to ideas :) Also just got in the hobby latex to use as a block.

Edited by coop

Share this post


Link to post
Share on other sites

Sounds like a good enough reason to me for black. Just make sure they're well defined and it should be cool.

Share this post


Link to post
Share on other sites

I think so too, that's why I am making sure I get the tools that will give me the best definition for the effect. I think the matted bevelers in combination with the smooth will give me that. How are you applying the latex?

Share this post


Link to post
Share on other sites

Like to see how this turns out, make sure you post some finished photos in the show off area

Share this post


Link to post
Share on other sites

I think so too, that's why I am making sure I get the tools that will give me the best definition for the effect. I think the matted bevelers in combination with the smooth will give me that. How are you applying the latex?

With a brush - good and heavy.

Share this post


Link to post
Share on other sites

Got the designs cut in yesterday, I have some scrap designs that I am testing different tooling on to see which work best. This is only the second design that I have used a swivel knife on and really need to upgrade the blade when I get more funds

.999311_10200642467642252_615282680_n_zps1867da85.jpg1004762_10200642522123614_2086122887_n_zps44cf80d7.jpg

Share this post


Link to post
Share on other sites

This is only the second design that I have used a swivel knife on and really need to upgrade the blade when I get more funds

Got a closeup of the design?

For your blade, save some money up now and get a good one ASAP. Go without soda for a couple days, make coffee at home, something. Barry King blades for "Tandy and Other" barrels are only about $15 and it will make you a lot happier. You can get a different barrel later that will be a lot smoother, but for now focus on the business end.

But, I really want to take a closer look at your cuts there. There's some very important stuff we may want to address.

Share this post


Link to post
Share on other sites

Share this post


Link to post
Share on other sites

So, what I'm most concerned about is your primary strap design with the flames. Everytime something gets thin and tapers to a point like that, the cut depth needs to gradually get shallower towards the tip and fall short of actually connecting. What you have here is the possibility of an overdramatic "disaster". basically, there's not material there to hole the tip of your flames onto the leather, so it's going to splinter up on you. By leaving them disjointed, you connect the line with your beveling alone. Also, you never cut deeper than the piece is wide. So, just feather those flames out and leave the tips disconnected and finish it off with your beveler.

The other thing, which is a hard one to grasp, is the concept of depth when overlapping items. ALL of your cuts are at the exact same depth right now, which means that no matter how it's tooled, it's not better than a 2D drawing. We're working with a 3D medium here, so our work needs to reflect that.

Look at your flames the way you have them cut. With this perspective, the flame on top (closest) is the EXACT same distance from the "background" (infinite space), as the flame that's sitting directly underneath it (furthest), as well as having that same amount of space between them. How is this possible? The same thing goes for your T overlapping the D. They're both physically the same distance away, but we know by the design that the D is further away than the T. So, to make it easy I'll focus on that one when describing the technique and you just apply it to everything else that overlaps.

Since the T overlaps the D, any line that is above the D needs to be a little lighter to show that there's less space between the two (let's call it 1 foot in regards to perspective). So, we're looking at this D and T sitting in the distance and we see that the T is closer to us, followed by the D that's 1 foot away, followed by infinite space. That means that the deepest cuts should be those that outline the T above the infinite space (since that's the largest amount of space we're dealing with), and the second deepest cuts need to be those outlining the D, since it has a little less space between it and the background. And, as mentioned, the lightest cuts will be those separating the two letters because there's only a little bit of space between them.

Sign up for these free lessons here. There's some awesome stuff there in regards to depth and perception. Study it, practice it, master it in your mind, then give it another shot and see the difference ;)

http://paintingcow.com/content/index.php/publications/free_lesson_sign_up/

Share this post


Link to post
Share on other sites

No doubt, that totally makes sense. I understand that concept, I draw a lot of black and grey art. I had read so much on designs not being carved deep enough and I have a heavy hand, (must be the bass playing) that I was focused on that aspect and didn't even think about that. I will just have to use the tools and try to shade heavy to light, and maybe even reverse the bevel it towards the end of the flames. Might even texture the flames this time. I have several cut out on scrap so I'll see what I can come up with. Thank's for the link, just signed up.

Share this post


Link to post
Share on other sites

I just used the B 701 and the A 104 for the tooling this time. I will invest in some more tools on the next project. I see how the depth of the cut relates to the image and will incorperate that in on the next design. Over all it has not turned out to bad for my firt tooling job I guess.IMG_20130711_124334_zps73a704de.jpgIMG_20130711_085451_zps447a2c5c.jpg

Right side up.

Edited by coop

Share this post


Link to post
Share on other sites

So far hasn't turned out too bad, I was able to keep the end of the flames from lifting or folding over but will def let the tooling create the ends next time.

post-40151-0-78334800-1373901781_thumb.j

post-40151-0-22285800-1373901789_thumb.j

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Create New...