Jump to content
skyblast

Getting Dye To Take To Leather?

Recommended Posts

I think that I am using the right products but I think I may be using them in the wrong order.

Here are the steps I use after a holster has been assembled and burnished (burnished using only water).

1) dye and let dry for a few hours (Feibings non pro dye)

2) using a dry cloth wipe off excess dye.

3) Spray on Saddle Soap to clean off any dye that did not take...let dry

4) Dye again let dry over night

5) Lexol to moisturize

6) Resolene (if only the dye looks good)

It is in step 5 where I have been noticing dye coming off. Dye coming off to the point where I can seen bare leather showing through.

Any suggestions? I get the feeling that I am way out of whack here.

post-11669-127869789996_thumb.jpg

Share this post


Link to post
Share on other sites

I think that I am using the right products but I think I may be using them in the wrong order.

Here are the steps I use after a holster has been assembled and burnished (burnished using only water).

1) dye and let dry for a few hours (Feibings non pro dye)

2) using a dry cloth wipe off excess dye.

3) Spray on Saddle Soap to clean off any dye that did not take...let dry

4) Dye again let dry over night

5) Lexol to moisturize

6) Resolene (if only the dye looks good)

It is in step 5 where I have been noticing dye coming off. Dye coming off to the point where I can seen bare leather showing through.

Any suggestions? I get the feeling that I am way out of whack here.

My sequence goes something like:

1 I use Lexol as I am tooling the leather.

2 Neatsfoot oil let stand over night

3 Dye only once let stand until dry

4 Wet leather and apply antiquing paste while wet.

5 Wipe off paste immediately. Dry overnight

6 Rub on NeatLac using cloth.

7 Aussie Cream or Leather Balm

Done

Dave Theobald

Share this post


Link to post
Share on other sites

I'd recommend dying the leather before assembly, certainly before molding.

The molding/burnishing is probably inhibiting the dye from penetrating.

But oil after all molding is complete.

Share this post


Link to post
Share on other sites

Try Feiblings Pro Oil Dye in your sequence. It's all I use. Eveery time I stray from it, I am not satisfied with the results.

Bondo Bob

Share this post


Link to post
Share on other sites

My sequence goes something like:

1 I use Lexol as I am tooling the leather.

2 Neatsfoot oil let stand over night

3 Dye only once let stand until dry

4 Wet leather and apply antiquing paste while wet.

5 Wipe off paste immediately. Dry overnight

6 Rub on NeatLac using cloth.

7 Aussie Cream or Leather Balm

Done

Dave Theobald

Dave,

can you explain how you use Lexol while tooling? do you use it in a casing solution? or just straight from the bottle?

i mix the casing solution that contains Lexol, but when i use it i have a little trouble getting an even dye job. (i air brush fiebing's pro oil dye) i wonder if i should be using a deglazer after tooling, but i worry if wetting again will dull the tooling impressions.

also, how do you apply neatsfoot oil? can that stuff be air brushed on?

thanks for any help,

ken

Share this post


Link to post
Share on other sites

Try Feiblings Pro Oil Dye in your sequence. It's all I use. Eveery time I stray from it, I am not satisfied with the results.

Bondo Bob

Thank you, Bondo Bob, . . . thought for a while I was alone

I have one exception to the above, . . . it is a special color I cannot (haven't figured it out yet, truthfully), . . . get using Pro Oil dyes. Other than that, . . . Pro is my only dye for all my projects.

May God bless,

Dwight

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Create New...