Jump to content
kayrunp

Looking For The Right Tool For Snipping Copper Rivets

Recommended Posts

I bought 7in end nippers from Home Depot for the task of cutting the copper rivets. My small hands just can't get it done with this tool. I figure its a crap tool and I don't have the power. What tool do I need?

Thanks!

Share this post


Link to post
Share on other sites

The tool you have is what i have always used. If it's where can put the end of one handle on your bench and squeeze that will give you more power or you may find some with a longer handle and that would be easier for you i think. If you go looking again take a rivet with you and see if you can cut it before you buy.

Share this post


Link to post
Share on other sites

I use compound action end nippers. The ac tion makes them cut much easier. Osborne makes a decent enough smaller one but if you hunt old antigue stores look for a pair of Schollhorn-Bernard compound action end cutting nippers. I buy them for $5-10 when I see them. Rarely are they worn much.

Share this post


Link to post
Share on other sites

Thanks Bruce and dirt clod! I found a pair of compound action end nippers on eBay and bought them, hopefully this will help me out.

Share this post


Link to post
Share on other sites

It'll cost you a 20 maybe more, . . . but a good pair of Klein lineman's pliers will chop them babies right now.

I used to do electrical work, . . . kept the tools, . . . you don't need to guess what I use.

You also may be using them wrong, . . . you need to get that rivet down as far into the cutting slot as you can. Your max pressure is down there.

The "ideal" tool is a pair of angled side cutters, . . . also made by Klein, . . . but unlike the pliers, you would only use them for rivets, . . . the pliers would have a few other uses, . . . side cutters, not so.

May God bless,

Dwight

Edited by Dwight

Share this post


Link to post
Share on other sites

+1 on the Klein lineman pliers

Bro Tim

Share this post


Link to post
Share on other sites

Hi Bruce,

Did I get the wrong tool? It's too narrow of an opening for the rivet.

Hi Bruce,

Did I get the wrong tool? It's too narrow of an opening for the rivet.

post-27014-0-58447300-1366641826_thumb.j

Share this post


Link to post
Share on other sites

It looks like the right tool, just the wrong size if the jaws won't open enough the get the shank of the rivet between them.

Share this post


Link to post
Share on other sites

Hi Bruce,

Did I get the wrong tool? It's too narrow of an opening for the rivet.

Hi Bruce,

Did I get the wrong tool? It's too narrow of an opening for the rivet.

Hi, take the pliers apart and remove some of their edges on the grind stone so it gets a bigger bite. (It looks like it possible to take apart). Be careful and keep it cool so it does not get blue and loose its tempered.

Tor

Share this post


Link to post
Share on other sites

I use cheap 16" hoof nippers, they are about $14.00 at Harbor Freight, Jeffers or kv supply.

Share this post


Link to post
Share on other sites

I ended up getting some greenlee diagonal cutting pliers. My wee hands seem to be able to mange these and they are sharp and appear well made. Now onto getting a nice dome on these rivets. Thanks for your help!

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Create New...