All Activity

Yes i see

I have kept some old shuttle drivers from a parts lot I bought some years so. The one on the left is close what you measured but I have to find my caliper... but I´m almost certain that yours is the machine with the smallest hook. Later more...

Was thinking you might check the Needle scarf size ? , Shorter length Scarf limits Hook travel, and some needle manufactures have longer length Scarf . Longer Scarf, the Hook will be able to move past the top and bottom of Scarf in little wider path on each needle stroke . Wider Scarf also lets you get more ZZ width without tapping top and bottom of the Scarf with the Hook, and help stop Hook wear. - -

Wanted to try a building, The Alamo seemed like a good project. It was more difficult than anticipated, larger size would make it easier. The size was 7.5 x 10, seemed big enough when printing the piece, plus it is hard to find a lot bigger piece on a belly. With the price of bellies it gives me more freedom to try and not be afraid of the cost of failure, just have to read the leather for proper moisture content.

I posted a 4-month review here: https://leatherworker.net/forum/topic/131750-review-of-jianglong-341-after-4-months/#findComment-784187

Thank you!

I made this primarily to use with my lathe but it may be useful for working on sewing machines etc. Copper face one end, nylon the other, copper was melted from motor windings. I found that copper is a pain to turn in the lathe as it galls and creates a rough finish!

Halloween; I prepared a large orange bucket with plenty of sweets (treats). I also included a few baby potatoes, as a sort-of 'booby' prize The childer came to my door. I got the bucket and told them to dive in and take lots. One we lassie got a spud. She laughed as she exclaimed 'I got a potato'. Then all the others cried they wanted one too. I tried to tell them it was a trick but they weren't listening They all crowded round the bucket and would you believe it the buggers err, the wee darlings all got a spud each! and were really happy There goes my Sunday dinner spuds

Hello Constabulary I have finally managed to get the measurements you asked for. Fence is 7 mm high and the diameter of the shuttle driver is 18.5 mm. Thanks

its called a ring clamp because the metal ring around it holds it together and makes it work, not because you use it to hold rings necessarily.

@AndreaIbis You should be posting using English. It is the language for this site. You have included English before so I guess it slipped your mind with these posts.

Beautiful work

So its been a long time since I have been on here (2018) I recently was sidelined with surgery and had more time on my hands. They wanted me using my hands, so I did leather work for some occupational Therapy. Feed back is welcome. I tend to make them for gifts. I never seem to feel like my work is professional enough to sell, but I have been asked lately by some professional crafters/artisans in the area to join them at a show. I am better a making than pictures

Ich habe auch noch dieses rot eingekreiste Teil übrig, von dem ich nicht weiß, wofür es ist und wo ich es hinstellen soll. Edited to add English Translation I also have this part circled in red left over, which I don't know what it's for or where to put.

Nach fast einem Jahr habe ich es endlich geschafft, alles zusammenzubauen und die ersten Tests durchzuführen. Es war gar nicht so einfach, ich bin schließlich kein Nähmaschinenmechaniker, aber sie funktioniert. Nur die maximale Zickzackstichlänge von 9–10 mm ist nicht wie erwartet (statt 12 mm). Vielleicht muss man da etwas einstellen, aber ich komme im Moment nicht drauf. Es gab ein kleines Kompatibilitätsproblem mit den Zahnrädern und den Schrägverzahnungen, da sie nicht richtig in das vorhandene Zahnrad passten. Mit etwas Schmirgelpaste habe ich die Maschine ein bisschen gedreht, und dann hat es geklappt. Edited to post Google Translation: After almost a year, I finally managed to assemble everything and do the first tests. It wasn't easy at all; after all, I'm no sewing machine mechanic, but it works. Only the maximum zigzag stitch length of 9–10 mm isn't as expected (instead of 12 mm). Perhaps something needs adjusting, but I can't figure it out at the moment. There was a minor compatibility issue with the gears and the helical gears, as they didn't fit properly into the existing gear. I used some emery paste to rotate the machine a little, and then it worked.

Similar to how I do it. I machined an arbor for the 60mm blades which I spin in a lathe and sharpen using a post grinder. I use a very fine grit stone which is followed up with a leather strop. I have about 20 blades and I sharpen a batch when about 1/2 of them need sharpening. Yeah, I know these blades are not pricey but my Dutch genetics won't allow me to waste money.

@Constabulary Variations like what you found seems to be somewhat common with some items I got from the orient in the past. Also the lack of good finish on parts, such as presser feet for the 801 bell skiver, have been a minor irritation but not uncommon even from touted & expensive US manufacturers/resellers. I'm fortunate that I have the tools and skills to finish or modify items to get them to work properly. BTW, the items I ordered are now in country and should arrive in about a week.

I was just selected as a tester for EngraveFill Pro. I should go live in the next couple weeks, but WOW am I impressed. Cool thing is, you only pay what you generate. No $300 programs! check it out. I am in no way associated with them, just a tester, but they seem like nice folks. https://engravefill.app/?fbclid=IwY2xjawNzE-pleHRuA2FlbQIxMABicmlkETEwR1lxM3p0RmljTWE0a3VMAR64tK9fXckb7w-6E-TNOLTRVzfAAHNsNPu1eLJrSl3CKLo7wEgeLRGHwR3kKw_aem_1tv2YBQc8KI2ve2MMQ98lw&payment_id=pay_1VKVbNuCXXuqulKKitxEJ&status=succeeded#/ On Facebook https://www.facebook.com/groups/1359934906135899

If you cannot get the gear to move, you could loosen the shaft again, and move it over the right number of teeth to bring your timing back to what you had before.

There are three set screws to loosen. How many did you loosen? Once all three are loosened, if still not moving you can add a few drops of diesel and let it sit to dissolve some of the corrosion, if that's the issue. You can also screw one of the set screws partway out, then place an end wrench (or spanner wrench) around the gear, using the protruding part of the set screw for the wrench to grab onto. (Go gently though)

So I’m wanting to use a Preval unit, but I’m mixing my dye and don’t want to mix more than I need. Is there a “minimum” amount needed in the bottle for the sprayer to work properly? TIA, AZR

As a follow-up, I guess, is there any change in technique when using both oil- and water-based dyes? Wow I really feel like a noob again after finally getting some NFO from Tandy (they couldn’t get any from the warehouse for MONTHS!)… — AZR

Ok, simple question (maybe)… Does water- vs oil-based dye affect how you use NFO? Is the typical oil/water separation even a concern? Ive been watching some videos from the University of YouTube, and I’ve noticed that they’re all using Fiebings Pro, and not water-based (I prefer the Pro dye myself, but I happen to have a water-based dye for this project), and I don’t want to ruin a piece by lifting or smearing the dye. TIA, AZR

I'll get a new left toe foot but have to place a new order - thats okay for me considering the fairly low price of the feet. They for sure have something I could use. I also found some interesting cheap feet for the Adler 67, 167, 68, 168, 69, 169, 267 and so forth "line" in their store: https://de.aliexpress.com/item/1005008687919538.html nutin for me Singer Idjit but looks like a good deal for the Adler folks 😉

The first few pictures are all the same style but in many different variations. This has become a great seller. The last picture in this style is still in progress. I am waiting on some hardware. The crossbody was a very tedious build. I love the strong color contrast.