Jump to content
Dave9111

Moving Industrial machines around the shop and outside

Recommended Posts


I have my share of industrial machines and I sometimes want to move them around both in the shop and outside for a larger canvas job.  Sometimes into a box trailer that has a ramp door.
I have flat moving dollies, but small wheels don't make rolling easy over uneven pavement.  And they don't work at all in gravel or on grass.  Yep, off road sewing!   I have some large covers to modify and alter and putting the machine in the lawn under a tree can work in nice weather.

What do you guys do?   

This has come to a head since I bought a two thread chainstitch machine and the head is really heavy - well over 100lbs and I want to be able to move it without planning for back surgery.

My machines all have the common K stands.   On the lighter machines (like a Pfaff 1245), I have mounted casters on the bottom of the K legs.  And that works in the shop.   But that's about all.  

Thanks,  Dave

 

Share this post


Link to post
Share on other sites

find a used Hoyer lift on CL or FB marketplace.    I recently saw that recommendation.   

Share this post


Link to post
Share on other sites

Mount them on a little trailer with a bench seat? 

 

Share this post


Link to post
Share on other sites

Hoyer lift.   Gosh I think my sister in law just sold one from my mother in laws house.    Never thought about that.

I have looked at some commercial solutions and it seems like the lift has to pickup the table top to go "off road", or off a hard floor.   Looking at my machines, that is really the only common pickup point.

So I will make something up and share it when I'm done.  I'm thinking a 1/2" or 3/4" steel pipe frame, some large air tire casters I already have should make up the bulk of it.  

A lever mechanism (maybe?) to raise the machine, etc.  Or maybe just tip the frame?

Thanks for the ideas.

I do have a little trailer I'm not using...  hmmmm...

Edited by Dave9111

Share this post


Link to post
Share on other sites

Dave9111,
I use a Hoyer type lift for lifting heads that are too heavy for me to handle out of tables, but it doesn't take much of a gap in a concrete floor to stop the Hoyer if it's moving slowly. If modified with much larger and wider wheels, I believe the type of lift in the picture would be better suited for what you want to do. The hook hinges at the top, and hooks under the top cross member of a K-leg as long as the leg is close to the edge of the table. Place the hook in position, crank up and you're on your way. It will work on longer tables, but with so much leverage at the other end, it's best to crank up a little and then manually lift the other end. Let me know if you want any measurements or other info.

ism mover.2 - Copy.jpg

Share this post


Link to post
Share on other sites

I've decided that I'm going to lift the machine via the table top.  

There is a couple of machines on the web that can do this but they are quite elaborate.  I'm going to try and keep it simple. 

I like the jack simplicity but I don't think lifting from the K leg even at the top is a good idea for me.  Reason being that I have one really heavy machine head, and I'm pretty sure the k leg wouldn't stand the strain.  

Share this post


Link to post
Share on other sites

I think I'm the one that started the Hoyer lift recommendation. At least started recommending it a few years ago. I use it to lift entire tables with machine from the end.  Using a couple of adjustable straps I made. Since it's made for moving up to 400lbs through doorways it works well.  I also use it to lift 166 lb Class 7 heads and 30" long arm 144's.  Working on a Class 7 when you can reach the top and the bottom of the head is a whole lot easier than reaching or crawling under a table.   I've also used the lift to put them in and out of a van or truck. They go under the vehicle just like a bed.  I have about 18 head on the first floor of my house and another 35 or so downstairs. So I bought two used lifts.  For around $75 each.  Often left over when an elderly relative moves to a care facility or passes.  Living alone most of the time the lift makes it easy for me to move all but the biggest tables around.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Create New...