Jump to content
Cattle Hide

Handmade Tools

Recommended Posts

The following photos are of the various tools I have made to fabricate holsters, sew leather and a tool rack for stamping tools.

These are holster boning tools made from UHMW (Ultra High Molecular Weight) Polyethylene. These were a bear to fabricate as the material is extremely abrasion resistant. I used a combination of sanding, filing, buffing with a raw cotton wheel (No Rouge) and final polishing on a piece of typing paper! Don't laugh it works great on plastic. 6" long by 3/4" wide scale fro comparison.

post-13946-039876500 1312216597_thumb.jp

This is a power edge slicker made from a craft store spool and 3/8" bolt and washers. Canvas is tacked with small brads and saturated with natural saddle soap.

post-13946-026421700 1312216599_thumb.jp

These are knives made from a power hacksaw blade (At top of photo, unmodified). The lower knife was made 30-40 years ago by my father who was a tool maker.

I sharpended these with the various instructions found here in numerous posts. The old knife is so sharp it practically falls through leather. Thanks Dad....

post-13946-030501300 1312216601_thumb.jp

This is a horizontal stitching pony made from dimensional poplar wood available from Lowes and other sources. Scrap pieces are included to show how it works.

Jaws are leather lined and simple clamps are used to hold closed and to the table. Table clamps left off for clarity.

post-13946-013875100 1312216606_thumb.jp

post-13946-030227300 1312216604_thumb.jp

This is the rear of the pony showing how one can add leather shims to keep jaws parallel

post-13946-085635000 1312216602_thumb.jp

This is my strop made from poplar and poster board with red rouge

post-13946-058969100 1312216607_thumb.jp

Stamping tool rack made from dimensional poplar using my drill press with milling vice. 24" long holds 46 tools of various sizes and diameters.

post-13946-088354400 1312216608_thumb.jp

post-13946-004521700 1312216610_thumb.jp

post-13946-048101400 1312216611_thumb.jp

Share this post


Link to post
Share on other sites

Necessity is the Mother of Invention..........you did well.

Share this post


Link to post
Share on other sites

Making your own tools ROCKS! Congrats on your ingenuity. Inspiring!

Share this post


Link to post
Share on other sites

Very Kewl!

Share this post


Link to post
Share on other sites

Nice! I like making tools as well and its neat to see what others are making.

Share this post


Link to post
Share on other sites

I really like the job you did on that tool rack!! Convenient, keeps all the tools at hand and keeps them safe. Now if I can train myself to put my tools BACK in the rack, I'll be a happy camper! :)

Knipper

Share this post


Link to post
Share on other sites

Great job on all those tools! (and great job on that holster you posted in the holster forum- very nice).

The bottom knife in the picture looks very similar to a Klein wire stripping knife I had. We've got some old big hack blades at work... I think you just inspired me to give it a try ;-)

I made a mallet out of that UHMW PE, and a wide slicker. It does takes a lot of work to get 'em smooth! I don't think I went nearly a fine with my polishing as you. I bet yours are a joy to work with.

Beautiful tool rack too- there's nothing like having your tools right where you want them when you need them. I like the little padding under the bladed tools. Nice touch.

Nooj

Share this post


Link to post
Share on other sites

Thanks Nooj for all of the positive comments.

I had a vision for all of the tools and kept working until I got to where I thought I could. As usual this got me in some trouble as it did take a lot of time to do the UHMW tools. The good news is that this material is great for slickers. As you know from having worked with the stuff it actually feels waxy it has such a low coefficient of friction. Made the molding of the holster easy.

Thanks for your comments on the tool rack. The pads for the cutting tools are self adhesive foam "Feet". They are about 1" wide by 3" long in the package. I also placed a couple under the the rack to keep the wood off the bench.

Next project is another holster and some 4" square coasters of various designs. This will give me tooling experience and a pile of gifts when the holiday season arrives.

Share this post


Link to post
Share on other sites

Hi Everybody,

Here are a couple Stitching related handmade tools, I made a couple years ago. The first one is my "Rapid Repeater",,, it uses an awl, to punch the holes for hand stitching. Makes it a lot faster,,, & keeps everything in a lot better alignment. The next thing is my little stitching pony. It's made to sit on,,, so if I want to take my stitching inside,,, I can do that. I also have a stitching clamp I use quite a bit, since I do a lot of Bible Covers & Portfolios,that require more depth.

Thanks for looking,,, these are just the tip on the "iceburg" Ed the"BearMan"

post-7175-048152500 1313033114_thumb.jpg

post-7175-091667200 1313033158_thumb.jpg

post-7175-091461000 1313033209_thumb.jpg

Share this post


Link to post
Share on other sites

The following photos are of the various tools I have made to fabricate holsters, sew leather and a tool rack for stamping tools.

These are holster boning tools made from UHMW (Ultra High Molecular Weight) Polyethylene. These were a bear to fabricate as the material is extremely abrasion resistant. I used a combination of sanding, filing, buffing with a raw cotton wheel (No Rouge) and final polishing on a piece of typing paper! Don't laugh it works great on plastic. 6" long by 3/4" wide scale fro comparison.

post-13946-039876500 1312216597_thumb.jp

This is a power edge slicker made from a craft store spool and 3/8" bolt and washers. Canvas is tacked with small brads and saturated with natural saddle soap.

post-13946-026421700 1312216599_thumb.jp

These are knives made from a power hacksaw blade (At top of photo, unmodified). The lower knife was made 30-40 years ago by my father who was a tool maker.

I sharpended these with the various instructions found here in numerous posts. The old knife is so sharp it practically falls through leather. Thanks Dad....

post-13946-030501300 1312216601_thumb.jp

This is a horizontal stitching pony made from dimensional poplar wood available from Lowes and other sources. Scrap pieces are included to show how it works.

Jaws are leather lined and simple clamps are used to hold closed and to the table. Table clamps left off for clarity.

post-13946-013875100 1312216606_thumb.jp

post-13946-030227300 1312216604_thumb.jp

This is the rear of the pony showing how one can add leather shims to keep jaws parallel

post-13946-085635000 1312216602_thumb.jp

This is my strop made from poplar and poster board with red rouge

post-13946-058969100 1312216607_thumb.jp

Stamping tool rack made from dimensional poplar using my drill press with milling vice. 24" long holds 46 tools of various sizes and diameters.

post-13946-088354400 1312216608_thumb.jp

post-13946-004521700 1312216610_thumb.jp

post-13946-048101400 1312216611_thumb.jp

Nice job on your work. The idea of making your knives with high speed steel is a good one. I've been using those saw blades for many years and they are the best ! Try making those plastic boning tools from bone,feels much better in the hand. Keep up the good work !

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Create New...