Treesner

New Tandy Craftool Pro Stitch Master made by Sailrite

Recommended Posts

3 hours ago, Ardenmare said:

I tried out the demo model at the Essex/Baltimore Tandy a couple of weeks ago. It's a nice machine, it was powerful enough to chew through 2 pieces of 5oz veg tan, although that's probably extreme for it. Really nice speed control. Just wish it could take a bit heavier thread sizes. 

I just checked out the Sailrite web page-the Tandy Stitch Master looks like a beige colored version of the Sailrite Ultrafeed LS1 portable that's been installed into a nice little table with their workhorse servo motor.  I like the smaller Tandy table, but for close to the same price, the Sailrite Fabricator sounds like a better deal with more capability. The site says it will take up to V-138 thread.

Here you can see a Sailrite in action!

 

Share this post


Link to post
Share on other sites

So.... I'm looking to buy another machine for holster making so I can make holsters and sheaths at the gun shows. Obviously I don't want to transport my cobra 4 and I'm not into the tippman boss.  Would this machine be good for this application ? Has to sew  up to 3 layers 6-7 veg. 

Share this post


Link to post
Share on other sites
36 minutes ago, devon22691 said:

So.... I'm looking to buy another machine for holster making so I can make holsters and sheaths at the gun shows. Obviously I don't want to transport my cobra 4 and I'm not into the tippman boss.  Would this machine be good for this application ? Has to sew  up to 3 layers 6-7 veg. 

The Sailrite Ultrafeed machines are good for about 1/4 inch, or 16 ounces of combined leather or vinyl. The maximum thread size is #92 (T90) bonded nylon or bonded polyester, which only has 15 pounds breaking strength. It will not safely sew a holster that can withstand any serious force on the gun. Quarter inch thick pancake holsters need to be sewn with #277 bonded thread (44 pound test per stitch), for security against stress on the stitch lines, which is way beyond the capacity of a Sailrite. You will need to look at harness and holster machines that are built to handle such heavy thread and the huge needles they require and extra strong pressure and tension springs that tension and pull up very strong thread into very dense leather.

As for portable heavy stitchers, there is the Cowboy Outlaw, the Tippmann Boss (both hand cranked), and the Artisan Toro 3200BT bench mounted motorized heavy stitcher. You can also sew holsters with a sole stitcher, like the Junker & Ruh sole stitcher or a Gritzner or Frobana hand cranked sole stitcher (rarer than hen's teeth)

Share this post


Link to post
Share on other sites
20 hours ago, devon22691 said:

So.... I'm looking to buy another machine for holster making so I can make holsters and sheaths at the gun shows. Obviously I don't want to transport my cobra 4 and I'm not into the tippman boss.  Would this machine be good for this application ? Has to sew  up to 3 layers 6-7 veg. 

as Wiz said, i've played with it some and it tops out at 10oz and the thread size limit would be a nogo for holsters, probably sheaths as well.  For the shows, you'll need something that will handle the size of leather and thread you need, other than hand-stitching there aren't many options for a lightweight transportable solution...even the boss and outlaw need a sturdy mount to keep it from jumping all over, you may as well carry the cobra with you unless power is an issue...

Share this post


Link to post
Share on other sites

This may be an ok or even good machine for what it is designed to sew.

The up and coming problem I foresee?.......

Tandy selling this to any newcomers with more scratch then knowledge about what they are buying. They will Shell out cash for a machine that probably won't suit their needs and wind up having to sell it for a big loss to fund the machine they need.

Also, these folks probably can't roll it back into their local Tandy when they have a problem with it. I wonder if that gets disclosed up front?

I haven't seen any comments about what pressure feet and such are available. I'm assuming they would be something from sailrite that comes with a hefty pricetag.

And another thing, I watched the video from stock and barrel leather (maybe the name is wrong)?  And this guy just couldn't say enough paid good things about this machine. Even went as far as saying it was looking like a better fit for his wallets and bags then his Juki. Really?

I commented and unsubscribed to his channel. I'm all for getting paid, but come on.

To tell the truth, I have no dog in this fight. But, I just see a lot of newcomers getting taken to the cleaners by Tandy on this one. And it puts an itch in my craw.

Just my .02.

Share this post


Link to post
Share on other sites

Plus 1 for Bikermutt!!!!!

Share this post


Link to post
Share on other sites

Cheap generic feet and other accessories avail for this machine all over ebay, etc, just like the rest of the mini walker machines (Reliable Barracuda, etc)

The motor Sailrite specs on these is the real star here and it will push pretty much any upholstery class machine to the limit of what it can do. Holsters though? Nope. Belts and wallets and such yeah but these machines max out there.

I would give a +1 vote to Wiz's suggestion of the Artisan portable setup for the 3200 BT machine. They are decent machines and that setup is specifically for tradeshows, events, rodeos and the like. If you were to lug a machine around to sew holsters and sheaths, and you didn't want to hand crank it, that would fit the bill.

Share this post


Link to post
Share on other sites

I agree with Bikermutt. It probably has it place in the market for certain items/locations but comparing it to his Juki 1508 is a real stretch at best. Hell that whining sound alone when it's running compared to a Juki 1508 or any other Juki for that matter, come on get real, no comparison.

kgg

Share this post


Link to post
Share on other sites

I've been through this many times.  

It's not a crime to hype, promote, sell, advertise, or provide only the good selling points of equipment offered.  A good sales person or team is supposed to do this, and it's their job.  

The problem I have is when people wind up surprised that the backyard go-cart with lawnmower engine they purchased is not the Maserati that they were told to expected to own.  You have to explain the limitations.  1st thing I do when offering a machine of this type is to qualify the customer by sitting them down on an industrial or asking them about their existing equipment to give a fair comparison.  This way the customer knows what it is they are getting and what to expect from the equipment.  If you are in production, machines of this type are great for on site job repairs, small jobs and the like.  They have a place in life, but are not going to replace a production quality canvas or sail making machine.  One guy who bought a machine of this type told be he lived on a house boat and cannot afford the space of an industrial.  Boom, perfect fit.  Right machine for the right customer.  

Edited by Gregg From Keystone Sewing
info@keysew.com

Share this post


Link to post
Share on other sites
47 minutes ago, Gregg From Keystone Sewing said:

I've been through this many times.  

It's not a crime to hype, promote, sell, advertise, or provide only the good selling points of equipment offered.  A good sales person or team is supposed to do this, and it's their job.  

The problem I have is when people wind up surprised that the backyard go-cart with lawnmower engine they purchased is not the Maserati that they were told to expected to own.  You have to explain the limitations.  1st thing I do when offering a machine of this type is to qualify the customer by sitting them down on an industrial or asking them about their existing equipment to give a fair comparison.  This way the customer knows what it is they are getting and what to expect from the equipment.  If you are in production, machines of this type are great for on site job repairs, small jobs and the like.  They have a place in life, but are not going to replace a production quality canvas or sail making machine.  One guy who bought a machine of this type told be he lived on a house boat and cannot afford the space of an industrial.  Boom, perfect fit.  Right machine for the right customer.  

well said Gregg ! Right machine for the right customer. Everyone has different needs.

Share this post


Link to post
Share on other sites
6 hours ago, Techsew Ron said:

well said Gregg ! Right machine for the right customer. Everyone has different needs.

Mr. Ron,

Thanks for that, glad you liked it.  I got that phrase from Onik, who recently passed.  I'm guessing that you may have known him as well?

Share this post


Link to post
Share on other sites
20 hours ago, bikermutt07 said:

This may be an ok or even good machine for what it is designed to sew.

The up and coming problem I foresee?.......

Tandy selling this to any newcomers with more scratch then knowledge about what they are buying. They will Shell out cash for a machine that probably won't suit their needs and wind up having to sell it for a big loss to fund the machine they need.

Also, these folks probably can't roll it back into their local Tandy when they have a problem with it. I wonder if that gets disclosed up front?

I haven't seen any comments about what pressure feet and such are available. I'm assuming they would be something from sailrite that comes with a hefty pricetag.

And another thing, I watched the video from stock and barrel leather (maybe the name is wrong)?  And this guy just couldn't say enough paid good things about this machine. Even went as far as saying it was looking like a better fit for his wallets and bags then his Juki. Really?

I commented and unsubscribed to his channel. I'm all for getting paid, but come on.

To tell the truth, I have no dog in this fight. But, I just see a lot of newcomers getting taken to the cleaners by Tandy on this one. And it puts an itch in my craw.

Just my .02.

Kind of like the Janome HD3000 they have better...honestly i can get it to do almost the same as the stitch master, just not quite the oompf and no servo/speed reducer...but it makes very nice stitches and feels pretty solid.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now