Evo160K Report post Posted February 17, 2019 Thank you. Quote Share this post Link to post Share on other sites
suzelle Report post Posted February 17, 2019 (edited) Looks like a bobbin winder. Not sure what machine it would go to though. What is the part number on it? Can't make it out from photo. Edited February 17, 2019 by suzelle Quote Share this post Link to post Share on other sites
machinehead Report post Posted February 17, 2019 Maybe for a Singer Class 6 or 7. Quote Share this post Link to post Share on other sites
Uwe Report post Posted February 18, 2019 (edited) It's the bobbin winder from a Singer 132K. I can only make out the "41896" number in the pictures above, but it matches the parts diagram of the Singer 132K. Looks like yours is missing the rubber "tire" that should sit in the groove and provide friction against the handwheel. Here's the picture from the SInger 132K owner's manual (Singer 132K Manual.pdf) This page is from the Singer 132K parts list (132K6_10_12.pdf) Edited February 18, 2019 by Uwe Quote Share this post Link to post Share on other sites
Evo160K Report post Posted February 18, 2019 Thank you one and all. Uwe, you nailed it, great information. Thank you. Thank you Suzelle and thank you Machinehead. Looks like the Singer Class 7 uses a similar part also . Quote Share this post Link to post Share on other sites
catskin Report post Posted February 18, 2019 5 hours ago, machinehead said: Maybe for a Singer Class 6 or 7. It also looks near exactly like the one on my Adler 20-2 even the base. Quote Share this post Link to post Share on other sites
Constabulary Report post Posted February 18, 2019 Singer 7 or 97 and Adler 20 winder have a longer pin for the bobbin and a wider filler tongue /stop latch. I´d also say Singer 132K / 133K but the coil spring is missing. Yes friction leather strip is missing too, they were attached with brass pins. Quote Share this post Link to post Share on other sites
Evo160K Report post Posted February 18, 2019 @ Constabulary Good to know. Thank you. @ Catskin Thank you. Quote Share this post Link to post Share on other sites
1985 Report post Posted January 7 I do have the similar types on my my class 7-33 but its missing its wheel and on my 132 k6 they look very similar to each other here is a pic but missing wheel class 7 Quote Share this post Link to post Share on other sites
Constabulary Report post Posted January 7 (edited) I don´t think you can get the OEM wheels anymore (well maybe... you never know). If I were you I would probably take a wheel from a different bobbin winder then wrap a piece of leather or PU flat belt around it and adapt it to the spindle. Spindle is present I guess? Other than that I would buy a table mount bobbin winder https://www.ebay.com/itm/143422223667 But it may need some modification as well. Edited January 7 by Constabulary Quote Share this post Link to post Share on other sites
1985 Report post Posted January 9 (edited) On 1/7/2024 at 10:08 AM, Constabulary said: I don´t think you can get the OEM wheels anymore (well maybe... you never know). If I were you I would probably take a wheel from a different bobbin winder then wrap a piece of leather or PU flat belt around it and adapt it to the spindle. Spindle is present I guess? Other than that I would buy a table mount bobbin winder https://www.ebay.com/itm/143422223667 But it may need some modification as well. Thought I may just get a old cast pulley wheel and find a spindle from some of my old metal bar from vintage machines I had, and either rubber or leather in the gap of the pulley, I have do have some old cast table bobbin winder, I never was lucky enough to have a metal lathe , It would of been useful ,in my tinkering with machines Edited January 9 by 1985 Quote Share this post Link to post Share on other sites
