Jump to content
TargetRockLeather

Hair-On Deer Hide Suggestions

Recommended Posts

Someone gave me a hair-on deer hide and asked to incorporate it into a sheath design. I'm looking for any suggestions on how to use it. I thought about making a normal cowhide sheath and covering it with the deer hide. I could glue it to the leather but I'm not sure what to do about the seam. I considered punching holes and lacing it with artificial sinew or perhaps leather lace.

Also, the hair is rather "fluffy" which seems like it will hide the shape of whatever I attach it to. I think it might make the entire project look like a ball of fur.

Does anyone have any suggestions or better yet, examples that I can look at for ideas? I've done a fair amount of searching and haven't found it used anywhere. I can't be the first one to attempt it. Any suggestions would be most welcome.

Share this post


Link to post
Share on other sites

Does it need to cover the whole sheath or can you do panels?

Is the hair short fluffy or long fluffy, if long you may be able to trim it?

Share this post


Link to post
Share on other sites

I guess I would consider it long fluffy. Panels might work on a larger project, but this one is probably too small for that. Maybe that's my problem, that the sheath is too small for what I'm trying to do with it. I never thought of trimming the hair. I might try that on a piece of scrap. This is what it looks like. In the last photo it's wrapped around the leather sheath and as you can see it just looks like a ball of fur lol.

003.JPG

004.JPG

005.JPG

006.JPG

Share this post


Link to post
Share on other sites

Looks like a fluffy hedgehog!

if it can be trimmed then all good

if not then an fluffy trim /tassel / mane?

Share this post


Link to post
Share on other sites

Or bottom half fluffy: with hair pointing down to knife tip & top half leather with some carving / stamp decoration 

Share this post


Link to post
Share on other sites

you could make him an awesome fur hat with hidden sheath. Just thinking outside the box, its not going to look like a sheath so make it look like something that fits fur and hide the sheath inside. Bracers maybe. 

 

Edited by chuck123wapati
more thoughts

Share this post


Link to post
Share on other sites
7 hours ago, HaloJones said:

Or bottom half fluffy: with hair pointing down to knife tip & top half leather with some carving / stamp decoration 

I sort of like this idea. I'm going to experiment with that.

 

1 hour ago, chuck123wapati said:

you could make him an awesome fur hat with hidden sheath. Just thinking outside the box, its not going to look like a sheath so make it look like something that fits fur and hide the sheath inside. Bracers maybe. 

 

I laughed when I first read this, but you're actually right. The hide does lend itself more to a fur hat than a knife sheath. Not sure how I would hide a knife in a hat though lol.

Share this post


Link to post
Share on other sites

My guess is it would look awesome if you took some dog clippers to it. practice on a scrap piece, gradually clipping shorter until you get the best look. I think a hairy look rather than furry would be the way to go.

Share this post


Link to post
Share on other sites

How about using it for some fringing...?

Share this post


Link to post
Share on other sites

If it is of any help I found that you can use the electric hair cutting trimmers with the different plastic spacers to trim the hair down to a lesser height and it works not too badly. Over here they call them buzz cuts I think. I'm not sure as I have been cutting my own hair with scissors for many many years and that's pretty rare as well.

Share this post


Link to post
Share on other sites

Check out Bob Blea's last post

I just came across it and it has hair on hide inserts for a wallet.... that might give you some idea's.

hth ... Regan :)

Share this post


Link to post
Share on other sites
10 hours ago, toxo said:

My guess is it would look awesome if you took some dog clippers to it. practice on a scrap piece, gradually clipping shorter until you get the best look. I think a hairy look rather than furry would be the way to go.

 

7 hours ago, RockyAussie said:

If it is of any help I found that you can use the electric hair cutting trimmers with the different plastic spacers to trim the hair down to a lesser height and it works not too badly. Over here they call them buzz cuts I think. I'm not sure as I have been cutting my own hair with scissors for many many years and that's pretty rare as well.

toxo, RockyAussie: I gave that a try. It works as far as making the hair shorter and more manageable, however the moment I trimmed the outermost layer of hair, it immediately lost the beautiful brown coloration and glossy fur look. The piece I ended up with might have well been squirrel hide lol. I'm uploading a picture of what I ended up with when I tried buzz trimming the fur. The piece on the left is obviously the trimmed piece.

2 hours ago, Rbarleatherworks said:

Check out Bob Blea's last post

I just came across it and it has hair on hide inserts for a wallet.... that might give you some idea's.

hth ... Regan :)

I found the post you are referring to. Yes, that looks like something I should try. I like the idea a lot. Thanks for pointing that out!

 

015.JPG

Share this post


Link to post
Share on other sites

For me I'd go further. How about clipping a bit more to get it even all over then really short down the middle so when you fold it they'll be a longer fringe around the outside curve? Just a thought. Don't shoot me ;)

Share this post


Link to post
Share on other sites

In case anyone is interested, this is what I came up with. I went with the inlay approach. It's not great but it was a good learning experience. I don't think I would attempt it again unless it's for a larger item. Thanks for all of the suggestions!

 

006.JPG

012.JPG

018.JPG

Share this post


Link to post
Share on other sites

It looks like you have a perfectly functional item there. With the benefit of 20/20/ hindsight, if I was making the sheath, I would have made the inlay, the same shape as the front piece of the sheath.

Maybe the hair could be shaped a little to make the bottom end of the hair not so square-cut. Maybe its just me being ultra-picky on a nice job.

Share this post


Link to post
Share on other sites
2 hours ago, Rockoboy said:

It looks like you have a perfectly functional item there. With the benefit of 20/20/ hindsight, if I was making the sheath, I would have made the inlay, the same shape as the front piece of the sheath.

Maybe the hair could be shaped a little to make the bottom end of the hair not so square-cut. Maybe its just me being ultra-picky on a nice job.

By all means be picky. That's how we learn! I actually had the same thought. The reason I made the bottom square and not all the way at the bottom of the sheath is that I thought the hair would look better flowing across the leather rather than hanging beyond the bottom of the sheath. In hindsight, as you said, continuing the shape of the sheath toward the bottom would have looked better.

Also I know that the edges of my leather are uneven. I admit that I rushed through it because I was just experimenting. I tore it apart and put it back together a couple of times so the the edges of the leather got a little beat up.

Thanks for the feedback!

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Create New...