ThomasBH

Hello, I've fairly recently picked up a Typical GC2605 Cylinder Arm machine specifically for binding the inside/raw edges of backpacks, pouches and some leather items. I'm specially looking for it to bind work pieces that are probably 1/8-1/4" thick using 1" grosgrain mil spec binding tape (5038 style). The machine came with a binder that I think was meant for using very thick binding like leather or webbing, but even using webbing does not produce good results. Here is a photo of some of the binders I've accumulated over the years that I've tried on this machine. Some are not meant for this purpose so I did some jury-rigging with tape to get them to mount, but alas, nothing will produce even remotely acceptable results. Most can't even bind on a straight flat piece. https://photos.app.goo.gl/xFoaS6pCGYHb4sb56 Any suggestions or help would be appreciated! Thanks

Hello, I just picked up an absolute steal on a slightly used "Toyoda 1508NH" which is a clone of a Juki 1508, NH but I can't find any information on the internet about this machine. It seems to be identical to the "Titan" branded one but I'm not sure. 1. The rear / non walking foot is very wobbly even when tightened...the hole is possibly too large? Should I be fine ordering regular 1508 parts? And how can I determine if its the foot or the piece the foot attaches to? 2. The needle size listed in the manual is 190 (and for actual Juki 1508 NHs) but the retailer / previous owner has 135 x 17 needles installed, which would be for the regular N version, not the NH version. My initial idea is the hook timing may have to be altered to work properly with the 190 size of needles...then I was thinking, maybe this machine is actually just an N version despite the metal plate riveted on the side. 3. There is a large plastic wheel with 1-6 settings on it on the top right...I think this is for adjusting the height of the walking foot? Can anyone confirm? I'm in Canada and any part sources or tips and tricks on this machine is appreciated. Thanks!

Solved! I guess that a "partially" compatible foot (cheap Aliexpress crap) must've knocked the other foot out of timing so the foot wasn't arriving at the exact time as the needle reached the bed, and only when it reaches at the same time does the 2nd foot actually raise and lower when the inner foot is at the bottom. It has an interesting mechanism for sure!

Thanks for the suggestion, but no, even with no feet attached watching the machine cycle the outer bar barely moves up and down at all, just a mm or two.

Hello, My Pfaff 145 was working fine for months, then all of a sudden after changing out feet the outer foot will not raise. Only the hand/knee lift will raise it now. If I look real close it moves about a mm when the inner presser foot is at BDC (bottom dead center) I've puzzled through all of the adjustment guides on the 1245 as well as google searches and can't find anything. Any suggestions? Thanks

Thank you kgg, i'll look into that company!

Thanks for the suggestions. I have this exact model of binder, same as you linked me. It came with a 24mm like the cutex one and it is too tight to fit the 5038 grosgrain well. Its possible that that style of binder is the way to go, just a different one that is larger. Also I would need to go up to 8mm. Also of note, the outer foot did not fit my 145, I got it to fit after filing down the top sides and it still doesn't fit well. The C shaped top was not wide enough to fit my machine. I also don't like this setup because it takes far too long to change over from the standard setup. I will be using this when I have to bind a bunch of stuff at once, but often I'm just binding small items in-between regular sewing when making bags.

Hello, Thanks for all the detailed replies! 1. By D shaped feed dog covers I am referring to the half-moon or D shaped metal feed dog cover than is common on many newer lightweight industrial machines. 2. I am using 1" mil-spec grosgrain (5038 to be specific) https://www.rockywoods.com/1-Grosgrain-Ribbon-Mil-Spec-Style-5038 3. The inline binders I have work fine but not with thicker builds or around curves. I'm looking at binding the inside of bags or shoulder straps that can often be 6-8mm thick. 4. In my ealier searches of this forum I didn't find what I was looking for, perhaps becuase I was just looking for Pfaff binder setups. Here is one from this form with pretty much what I'm looking to do: 5. The existing right angle binders I have that are meant for that top style of feed dog cover do not work, even if I drill holes because the L bracket will not be close enough to the needle. Basically in the bottom right of this photo you can see that the vertical plate/guide after the binder is too close with any normal feet. The idea is I want to keep my standard walking feet and just swap out the plates. 6. Here is a video of a guy with a Juki with pretty much exactly what I'm looking for. Thanks again!

Hello, I'm looking to get a single fold, right angle binder 1" in size that just mounts to the bobbin cover plate. I would like to use the standard feet for the machine (double outer feet) and be able to just swap the plates out. A swing away style would also be fine. Something like this, only would not require swapping out the feet: https://www.ebay.com/itm/292096884215?_trkparms=amclksrc%3DITM%26aid%3D1110006%26algo%3DHOMESPLICE.SIM%26ao%3D1%26asc%3D238901%26meid%3D7245e542c0774f9bb307900b4d433d75%26pid%3D101113%26rk%3D1%26rkt%3D12%26sd%3D122464199943%26itm%3D292096884215%26pmt%3D0%26noa%3D1%26pg%3D2563228%26algv%3DDefaultOrganicWeb%26brand%3DUnbranded&_trksid=p2563228.c101113.m2108 I already have the synchronized binder attachment with the binding feet and feed dogs, but it simply takes too long to change over. I have seen a number of small businesses on Youtube with this style on similar machines like the Juki 563. I have a couple of right angle binders from other machines that are designed to attach to those D shaped feed dog covers and investigated the idea of tapping new holes in one of my bobbin plates, but the part that screws to the plate would prevent the actual binder from ever getting close enough to the needle to effectively capture the binding, eg it needs to be further to the left. I also emailed Tennessee Attachments, but they did not get back to me. Any suggestions? Thanks!

After much more fiddling and a local sewing machine technician stopped by I seem to have gotten my 145 into a state that I'm pretty happy with. While the forward / reverse stitch length was the most noticeable issue when I first received the machine, after additional testing the inconsistent tension was of much more concern. My forward and reverse stitches are still not consistent, especially if I change the stitch length. (I have decided to just leave it at '2' for most purposes where I have adjusted it to match fwd/rev for at least 4 or 5 stitches) The tech found four issues: 1. The hook/bobbin assembly was not fully seated in its slot (maybe a couple of mm higher than it should've been) This caused this part to wobble: 2. The hook/bobbin assembly position needed to be rotated slightly(using the right hand screw that allows some horizontal adjustment) 3. The throat plate had been damaged/enlarged where the hook/bobbin case slots into it on the underside, this caused loops to form at the wrong time. Here you can see the closest throat plate with some damage/odd shape and the new binding throat plate in the rear of what it should look like. 4. Micro burs / sharp edges on some components Thank you all for your help, much appreciated. I have tried to include lots of photos and descriptions to help any future users facing issues. Feel free to DM me if you need any help yourselves. Also, for those interested you can get very cheap binding sets to have a cylinder arm style synchronized binder, this would work on a 145, 545 and 1245. https://www.aliexpress.com/item/1005003451959950.html?spm=a2g0o.9042311.0.0.14334c4d3mdpTs

So I've spend some time fiddling and reading manuals / watching youtube videos. 1. I adjusted the needle bar height to be the exact height of the outer walking foot so that it wouldn't collide, but this caused other issues, namely the hook point did not meet the scarf to grab the upper thread properly. Made some terrible sounds and broke a needle. I could not find a manual for the 145/545 mentioning the distance the needle bar should be at bottom dead center (BDC), but in a 1245 repair manual it mentioned 15mm. It was set to 15mm before I made these adjustments, so I just returned it back to 15mm. I am assuming that this aftermarket welting foot is the issue and am hoping the proper Pfaff foot doesn't strike. Can anyone confirm what the 145 H3 needle bar height should be set to? 2. Watching this video (also for a 1245) it states that the needle hook should be right in the middle of the scarf. My machine seems to be slightly lower than this. It mentions the needle bar should be at BDC, then 2mm up for the hook to meet the scarf. Mine is probably 3mm up, however it seems to be working fine. I also notice that the hook also hits and deflects the needle slightly, maybe 0.5mm. I see in another Cechaflo 1245 video he has his 1245 hitting the scarf slightly. Should I be concerned with this? Should I adjust it to be exactly 2mm and not touch the scarf? 3. Relating to both 1 & 2, my machine is supposed to be using the 134-35 needles but the previous owner gave me about 10 packs of 135-17s, which are about 1mm longer. So maybe he had timed the machine for the longer needles? Maybe because they were more available? I am going to try using one of these to see if it works any differently. 4. Will any of the above adjustments actually affect the forward to reverse motion of the stitch length?

Johnny, thank you for the help! My machine is a 145 H3 6/01. My needle is definitely new, I'm using the 134-35. I have also ordered a variety of feet (binding, regular and zipper) but alas, they are taking weeks to arrive. I'm definitely going to be trying all of the sections you mentioned, however it is very "dense" filled with jargon I'll have to look up, so it will take me a while. Even 'hook point' or 'centerline of the needle' are confusing to me. I will keep reading and look some of these terms up. I will send you a PM for the manual.

Thank you very much Johnny. Reading point 9.2 it mentions the needle bar should not strike the raised foot. My outer foot does strike the needle bar when raised in this situation. Should I attempt to raise the needle bar? I think this will cause issues with the hook timing unless I had a longer needle. I'm using 134-35 needles, but this machine also came with a lot of 135-17. Also, the only foot it came with is a welting foot and it appears to be after market, which is why it may be striking the bar.

Thanks Michiel. Unfortunately I have not been able to located a service manual for the 145. Does anyone know where I can download one?