Jump to content

Recommended Posts

  • Members
Posted

I'd love to post a pic of the ring. But I need more info, maybe pics. What leather to use, etc. I'm sure this is a great way to make this but it doesn't make sense to me. Do I use glue or what? I need to get a nice looking ring done. This woman's Husband is allergic to metals so needs this as a weddiing band.

No problem Noah.

Make sure to post some pics of your ring for us!

Rick

skyout

  • Replies 26
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

  • Members
Posted

Here is an experiment I did today, but I don't think it would be nice enough as is for a wedding ring. it might still help:

1. I traced the inside of my ring on the back of 6oz leather.

2. drew a circle slightly smaller and a circle slightly bigger than my tracing, so that the line I traced was dead in the middle and the two new circles were as far apart as I wanted the width of the ring to be.

3. Cut out the O, using scissors for the outside and a chisel for the inside - this made it kinda rough so later I would want to sand it or something

4. wet it

5. twisted it so that the top grain was on the outside and the rough was on the inside. At this step the leather stretches some but not as much as you might expect

6. Squished it flat underneath that 30lb marble slab we use for hammering If I had a wooden dowel the right size, I would have cut a slice off of that to put in the center of it and put the whole thing under the marble

Now I'm going to let it dry, and maybe figure out a way to sand it some before I finish the edges. I might even harden it in hot water so it won't stretch any more.

-----------------------------

Based on how I understand the instructions and my experimenting, here is what I think you can try:

1. You need a core for your ring which you can make following the steps above.

2. Cut out a larger O out of some sort of garment leather and wide enough to wrap all the way around the first O.

3. Wet it and stretch it around the first O so that it becomes the skin of the ring all the way around

4. You might need to peel it up and tack it with cement once it dries?

I have not tried this yet, and maybe I don't understand the first instructions. Good luck and tell us what you end up doing!

  • Members
Posted

Thankyou. I will read this all and try it tomorrow. It's starting to storm abit and I have barn chores to do. Looks like fun.

Here is an experiment I did today, but I don't think it would be nice enough as is for a wedding ring. it might still help:

1. I traced the inside of my ring on the back of 6oz leather.

2. drew a circle slightly smaller and a circle slightly bigger than my tracing, so that the line I traced was dead in the middle and the two new circles were as far apart as I wanted the width of the ring to be.

3. Cut out the O, using scissors for the outside and a chisel for the inside - this made it kinda rough so later I would want to sand it or something

4. wet it

5. twisted it so that the top grain was on the outside and the rough was on the inside. At this step the leather stretches some but not as much as you might expect

6. Squished it flat underneath that 30lb marble slab we use for hammering If I had a wooden dowel the right size, I would have cut a slice off of that to put in the center of it and put the whole thing under the marble

Now I'm going to let it dry, and maybe figure out a way to sand it some before I finish the edges. I might even harden it in hot water so it won't stretch any more.

-----------------------------

Based on how I understand the instructions and my experimenting, here is what I think you can try:

1. You need a core for your ring which you can make following the steps above.

2. Cut out a larger O out of some sort of garment leather and wide enough to wrap all the way around the first O.

3. Wet it and stretch it around the first O so that it becomes the skin of the ring all the way around

4. You might need to peel it up and tack it with cement once it dries?

I have not tried this yet, and maybe I don't understand the first instructions. Good luck and tell us what you end up doing!

  • Members
Posted

Thankyou. I will read this all and try it tomorrow. It's starting to storm abit and I have barn chores to do. Looks like fun.

I just did a search for "ring" and came up with only one thread in 8 pages, but it took forever because I kept getting sidetracked. LOL

I know it won't work for you as it has metal on it, but here's one from 8thsinner that some others may enjoy.

http://leatherworker.net/forum/index.php?showtopic=20464&st=0&p=132252&hl=ring&fromsearch=1entry132252

  • Contributing Member
Posted (edited)

IMG_0234.JPG

One piece cut out like a donut, then wet formed over a mandrel (happened to be my mallet handle). I also used the tapered handle of my edger to help stretch the smaller circle to a larger diameter. There's also a bit of skiving on the flesh side, otherwise one side is drastically thicker than the other.

And yes, I remember someone saying I cheated by doing it on the computer.......<sigh>.

post-5374-126931732295_thumb.jpg

Edited by TwinOaks

Mike DeLoach

Esse Quam Videri (Be rather than Seem)

"Don't learn the tricks of the trade.....Learn the trade."

"Teach what you know......Learn what you don't."

LEATHER ARTISAN'S DIGITAL GUILD on Facebook.

  • Members
Posted

Sky I thought of braiding the ring abit bigger than I need and weaving some excess back into to make the size alittle smaller than I need, and glueing it firmly. Wonder if it would hold.

twinoaks that's what I would like to do. Guess I'll have to play with this all today and see what I come up with. I have a month to make it but would really like to surprise them with it much sooner.

I sure appreciate all the help & tips.

  • Members
Posted

IMG_0234.JPG

One piece cut out like a donut, then wet formed over a mandrel (happened to be my mallet handle). I also used the tapered handle of my edger to help stretch the smaller circle to a larger diameter. There's also a bit of skiving on the flesh side, otherwise one side is drastically thicker than the other.

And yes, I remember someone saying I cheated by doing it on the computer.......<sigh>.

Yes- this is what I was talking about in my post about this. Nice job. (although skiving isn't necessary, just a lot of wetting/stretching/molding).

  • Members
Posted

IMG_0234.JPG

One piece cut out like a donut, then wet formed over a mandrel (happened to be my mallet handle). I also used the tapered handle of my edger to help stretch the smaller circle to a larger diameter. There's also a bit of skiving on the flesh side, otherwise one side is drastically thicker than the other.

And yes, I remember someone saying I cheated by doing it on the computer.......<sigh>.

Cool, that is basically what I did, and so now I know some of the things I can do to make the one I'm still working on better :D

  • Members
Posted

Or you could try also try my version...

DSC01035-(1).jpg

post-7332-126940993798_thumb.jpg

Doing the right thing is bleeding for the cause.

Website

Facebook

  • Members
Posted

I had thought about just braiding some thin leather and tucking & glueing the end to the size needed. If I can't get this other method to work guess I'll have to. Thanks..

Or you could try also try my version...

DSC01035-(1).jpg

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Create New...