Trox Posted September 1, 2016 Report Posted September 1, 2016 The 45K came in a variety of different subclasses and even more different presser footˋs. Without knowing your/what subclass you are looking for a presser foot/ plates for is difficult. The only new stuff sold for the 45K Adler 5/4 and clones are the narrow harness foot manufactured in China (sold by Cowboysew, try Cowboy Bob, Toledo Industrial Sewing machines) You can see this harness foot in the site of Cowboysew.com . I think it would be very difficult to find the parts you looking for, you might be lucky. I had some of these parts before, unfortunately I sold them several years ago. I would advice you to specify what parts you are looking for with a picture and part number. This way it would be easier, somebody might have these old part but do not know what they are for. Good luck Tor Tor Workshop machines: TSC 441 clone/Efka DC1550, Dürkopp-Adler 267-373/Efka DC1600, Pfaff 345-H3/Cobra 600W, Singer 29K-72, Sandt 8 Ton clicking machine, Alpha SM skiving unit, Fortuna 620 band knife splitting machine. Old Irons: Adler 5-27, Adler 30-15, Singer 236W-100
Evo160K Posted September 2, 2016 Author Report Posted September 2, 2016 Trox, Good suggestion, thank you. Here are two lists of parts that I'd like to have.......one for Singer 45K25 and one for Singer 45K53. They're the lists I gave to Ralph's Industrial to check. I don't have pictures, but since I'm only wanting original Simanco parts, the Simanco part numbers should be adequate. If anyone has a part marked Simanco, it's easy enough to check the lists for that number. Thanks again, Trox.
Trox Posted September 2, 2016 Report Posted September 2, 2016 There always some old iron around you might be lucky if the add can be seen by enough people, "bump" it to keep it alive frequently. It's like someone asked me to sell the original saddlers attachment pack for my old Adler 5-27 (who's basically the same machine as a 45 K cyl.bed with jumpfoot) without buying the machine. I could not sell one without the other. That said, you can't get anything without trying; and there's a lot more Singer machines out there than Adlers. Good luck Tor Tor Workshop machines: TSC 441 clone/Efka DC1550, Dürkopp-Adler 267-373/Efka DC1600, Pfaff 345-H3/Cobra 600W, Singer 29K-72, Sandt 8 Ton clicking machine, Alpha SM skiving unit, Fortuna 620 band knife splitting machine. Old Irons: Adler 5-27, Adler 30-15, Singer 236W-100
Evo160K Posted September 3, 2016 Author Report Posted September 3, 2016 Yes, I will bump it from time to time. Thanks for the advise, Trox.
Evo160K Posted September 20, 2016 Author Report Posted September 20, 2016 LW member Uwe found a few parts for me. Thank you Uwe, thank you very much.
Evo160K Posted October 5, 2016 Author Report Posted October 5, 2016 LW member Constabulary found a couple of feet for me. Thank you Constabulary, thank you very much.
Evo160K Posted December 13, 2016 Author Report Posted December 13, 2016 Still looking. They're difficult to find.
Evo160K Posted February 6, 2017 Author Report Posted February 6, 2017 Any one know where I might find some of these parts? Thanks very much.
Evo160K Posted July 23, 2017 Author Report Posted July 23, 2017 Anyone have any or have a suggestion where I might look?
Recommended Posts