Pricking tool help!!

[bsshog40]

So I'm wanting to upgrade my pricking tools. Right now I have 6 spi angled tools. I'm looking for a set that I can use on my sheaths, holsters, pocket knife cases, etc....I only saddle stitch by hand.  So here are my questions:

Are round hole prickers better? 

What would be a standard mm spacing? 

What would be a decent priced brand? 

I was looking at some WUTA prickers on amazon. Any advice would be appreciated!!

Bobby

[PastorBob]

4 minutes ago, bsshog40 said:

So I'm wanting to upgrade my pricking tools. Right now I have 6 spi angled tools. I'm looking for a set that I can use on my sheaths, holsters, pocket knife cases, etc....I only saddle stitch by hand.  So here are my questions:

Are round hole prickers better? 

What would be a standard mm spacing? 

What would be a decent priced brand? 

I was looking at some WUTA prickers on amazon. Any advice would be appreciated!!

Bobby

I got my first set from Tandy.  It worked okay, but didn't seem very sturdy.  Mine are all angled chisels.  I have 3 different sets from Weaver with all different spacings.  The one I use most is the 5mm.  They are a little more, but I have not had to replace them.  I also rub mine over a clump of beeswax as i am going.

[bsshog40]

26 minutes ago, PastorBob said:

I got my first set from Tandy.  It worked okay, but didn't seem very sturdy.  Mine are all angled chisels.  I have 3 different sets from Weaver with all different spacings.  The one I use most is the 5mm.  They are a little more, but I have not had to replace them.  I also rub mine over a clump of beeswax as i am going.

This is the set I basically have now. 

 

Edited Monday at 04:28 PM by bsshog40

[BlackDragon]

It really depends on what you want your end product to look like. I like French pricking irons but I did sometime use diamond chisels. I dont like round holes because the holes tend to be bigger than the thread.

[bsshog40]

1 hour ago, BlackDragon said:

It really depends on what you want your end product to look like. I like French pricking irons but I did sometime use diamond chisels. I dont like round holes because the holes tend to be bigger than the thread.

Ya, I like my diamond tools. The sizes on them are 2.3mm, 3.1mm and 3.9mm. I have only used the 2.3mm on all my stuff. Not sure where the bigger ones would be used. I like the tighter spacing. 

[BlackDragon]

When I was hand stitching I mostly stayed with one size but depending on the item you may want to go bigger or smaller. 

If you're doing a wallet you may want a nice tight stitch but if your making a belt you may want to use a wider chisel. Stitching belts by hand can hurt your hands after awhile so using a wider chisel can lessen the amount of hole you have to stitch.

[bsshog40]

5 minutes ago, BlackDragon said:

When I was hand stitching I mostly stayed with one size but depending on the item you may want to go bigger or smaller. 

If you're doing a wallet you may want a nice tight stitch but if your making a belt you may want to use a wider chisel. Stitching belts by hand can hurt your hands after awhile so using a wider chisel can lessen the amount of hole you have to stitch.

Lol Ya, I have a couple belt blanks that I've been wanting to carve. I like the way stitching on edges of a belt look but, no way am I gonna hand stitch a belt. I would probably have to have 20' of thread laying all over to stitch it. Lol

Thanks for your replies my friend!

Bobby 

[TomE]

I use an overstitch wheel or these pricking irons to mark holes https://www.rmleathersupply.com/products/rocky-mountain-premium-pricking-irons.  I make the holes with Osborne sewing awls of various sizes.  A sharp awl works well for thick leather, irregular shapes, and sewing under fixed loops/keepers.  The awls get smaller as they are repeatedly sharpened, so I can match a range of thread sizes.     

[bsshog40]

3 hours ago, TomE said:

I use an overstitch wheel or these pricking irons to mark holes https://www.rmleathersupply.com/products/rocky-mountain-premium-pricking-irons.  I make the holes with Osborne sewing awls of various sizes.  A sharp awl works well for thick leather, irregular shapes, and sewing under fixed loops/keepers.  The awls get smaller as they are repeatedly sharpened, so I can match a range of thread sizes.     

Those are nice. I may have to save up for those. I have an awl also but I'm really not big on round holes. I also have a stitching wheel that I got a while back. I need to get that out and practice with it also. 

Thanks for the response!

[TomE]

5 hours ago, bsshog40 said:

Those are nice. I may have to save up for those. I have an awl also but I'm really not big on round holes. I also have a stitching wheel that I got a while back. I need to get that out and practice with it also. 

Thanks for the response!

A sewing awl has a diamond profile that pairs nicely with the pricking irons.  The tip of the awl is sharp and the shank is polished to stretch the hole, which closes up after the stitch is made.  Enables fine stitching with the thread filling the holes.

[bsshog40]

32 minutes ago, TomE said:

A sewing awl has a diamond profile that pairs nicely with the pricking irons.  The tip of the awl is sharp and the shank is polished to stretch the hole, which closes up after the stitch is made.  Enables fine stitching with the thread filling the holes.

🙂