Jump to content

Recommended Posts

  • Members
Posted
6 hours ago, Wizcrafts said:

Check to make sure that the top thread is staying all the way inside the tension disks

This happened to me a couple days ago on my Jianglong 341. The TEX 270 thread would be inside the tension disks at the beginning of the seam, but by the end of the seam the tension disks would be flat together with the thread only skirting their perimeter. That's when I decided to add some tension to the smaller/auxiliary tension disks right next to them, which I had never found a use for previously. But it seemed to keep the thread properly seated in the main tension disks.

In search of the perfect hundred-dollar servo motor with needle positioner.

friquant. Pronounced "FREE-kwuhnt"

  • Members
Posted
1 hour ago, kgg said:

I would do the drop test for tension on the bobbin thread

How does one do the drop test with a vertical hook shaft?
I tried it but the bobbin fell out of the bobbin case cap.

In search of the perfect hundred-dollar servo motor with needle positioner.

friquant. Pronounced "FREE-kwuhnt"

Posted
3 hours ago, friquant said:

This happened to me a couple days ago on my Jianglong 341. The TEX 270 thread

I think some of your problem is you are using Tex 270 (V277) which the machine is not rated for. The 341 / 1341 clones of the Juki LS 341 or 1341 are rated for a #24 needle which will accept Tex 210 (V207) but the machines typically will only sew that in thinner material. A lot of clone machines rate their machines on the max size thread you can stuff through the eye of the needle vs Juki rates their machine on what it can sew with the max size top thread and bobbin thread in max. sewing thickness. That is why you see the Juki LS-341 or 1341 rated for V138 thread not V207.

1 hour ago, friquant said:

How does one do the drop test with a vertical hook shaft?

Insert bobbin in the top cap and through the tension spring so the bobbin spins counter clockwise when you pull on the end of the bobbin thread. I leave about 4 to 6 inches of end thread dangling.

Place the bobbin and cap in the palm of your left hand.

With your right hand grab the end of the bobbin thread and lift the bobbin case of your hand. If there isn't enough tension the bobbin will just spin in your hand and probably fall to the floor. You should be able to lift the bobbin and case off your hand otherwise you have to tighten the little screw by turning it clockwise about 1/8 of a turn. You do not want to flat that little spring or unscrew the screw to much as if the screw comes out chances are you will never find it. Try again. When you get the tension just about right you should be able to lift it off your hand. Once you can lift the bobbin off your hand try giving the end of the thread a couple of quick jerks it should cause the bobbin to spin slightly and yet be lifted off your hand. 

kgg

  

Juki DNU - 1541S, Juki DU - 1181N, Singer 29K - 71(1949), Chinese Patcher (Tinkers Delight), Warlock TSC-441, Techsew 2750 Pro, Consew DCS-S4 Skiver

Posted
11 hours ago, friquant said:

The TEX 270 thread would be inside the tension disks at the beginning of the seam, but by the end of the seam the tension disks would be flat together with the thread only skirting their perimeter.

I forgot to ask if you could provide a photo of how you have your top threaded.

kgg

Juki DNU - 1541S, Juki DU - 1181N, Singer 29K - 71(1949), Chinese Patcher (Tinkers Delight), Warlock TSC-441, Techsew 2750 Pro, Consew DCS-S4 Skiver

  • Moderator
Posted

See the update I wrote in my earlier comments, up the page.

Posted IMHO, by Wiz

My current crop of sewing machines:

Cowboy CB4500, Singer 107w3, Singer 139w109, Singer 168G101, Singer 29k71, Singer 31-15, Singer 111w103, Singer 211G156, Adler 30-7 on power stand, Techsew 2700, Fortuna power skiver and a Pfaff 4 thread 2 needle serger.

  • Members
Posted (edited)
On 7/23/2025 at 7:38 AM, kgg said:

I forgot to ask if you could provide a photo of how you have your top threaded.

Here's how my top is threaded.

threaded-01.jpgthreaded-02.jpg

 

Edited by friquant

In search of the perfect hundred-dollar servo motor with needle positioner.

friquant. Pronounced "FREE-kwuhnt"

  • Members
Posted (edited)
On 7/22/2025 at 1:20 PM, Wizcrafts said:

You can turn the post with pliers to get a good angle coming out of the bottom hole.

Nice update!
Did you mean bottom hole instead of bottom disk?

Edited by Wizcrafts
I corrected a typo where I ended with the word disk insted of hole.

In search of the perfect hundred-dollar servo motor with needle positioner.

friquant. Pronounced "FREE-kwuhnt"

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...