How do I make a Cartridge Belt Slide?

[Larry]

I tried to make a pattern out of paper for a 6 cartridge belt slide for .357 mag and not having any luck. I tried making one out of scraps just to see how it might be done. I didn’t realize it was such a technique to it. Can someone help me out with some instructions or a source for how to do one? I’ve seen some pictures on the forum of some beautiful rigs with holster, belt and a slide that matches. Thanks everyone, this is all still very new to me. I’ve made the holster. Thanks again. Larry

[rhona]

Hi Larry,

I’ve made clocks, knife sheaths, everything else almost but never tried a holster! However, I have a friend who makes one of the most professional looking holster “conceal carry”jobs I’ve seen! Check out: Rhome of DGL he’s on LW. You can check his site: www.desbiensgunleather.com. I hope this helps.

MALIGAYANG PASKO!

Rhona

Baguio City, Philippines

http://rhonacarantes.multiply.com

[MBOGO]

Larry,

You will need leather for the slide, let's say 8-9 oz, and leather for the loops, under 7 oz. The leather for the loops will have to be cut to width, any ornamantation (?) done to it, dyed (?), edges finished. There are different ways to proceed, if you want the rim of the carterage to ride on a shelf, you will have the loops sewn onto another piece of leather which is sewn to the looped slide, or the rims are stopped by the loop. The loops are sized for the cartdrige and sewn in place, do not groove on the loop side, as the leather is thin, and the strength is a plus. Then fold the piece in half, (welt or no welt) and sew. You would probably be well to give yourself an extra 1.5 inches extra on each end, after cutting to center the loops after them all, then edging. Don't be discouraged if you have one or two practice pieces.

Marc

[DCKNIVES]

Yep, pretty much what Marc said.I do mine a little different as I slot my top piece and weave the cartridge strap through the slots and attach on the ends. I also put snaps on mine at the bottom.Dave

[MBOGO]

The instructions I gave have a downside, the loops can stretch out. The downside to Dave's method is if you pull out for a partial reload, the others can get loose. I did make one belt with a similar method to Dave's, but cut one end long, didn't secure it, and pull it tight when cartredges are removed. That was mentioned by Elmer Keith as one of his favorite patterns.

As for books on construction related to this, pick up a copy of Al Stohlman's Making Leather Cases, Vol I. All three of these books are great for techniques and how to.

Marc

[Larry]

Thanks, Marc and Dave for the help. After a couple of days and a lot of trial and error, I think I finally got it. I went with Marc's method because it worked out a little better for me. But Dave's method is good too. I have a cowboy rig done by Bill Weaver from Oklahoma (Leather, Guns & Etc.) and he used slots for the loops on my rig. He did a great job, as anyone who knows Bill will agree. I actually worked out measurements for the location of the stitching holes and cut my pieces then punched the holes with a 4 pronged diamond hole punch. Put it in my stitching horse and when I pulled the stitches tight the loops came right into position. The cartridges are real snug. I used the welt, folded over and glued. This is my first one and since its still new to me, my stitches are a little sloppy. My name is not centered and there are other things, but I just wanted to get one completed so I would know what to expect. I plan to make a good one and will take more time with it now that I know how it all goes together. Thanks again. Larry

Edited December 26, 2009 by Larry

[Lobo]

All the high points have been well-covered. The only thing that I would add is wet-forming the loops to the cartridges, stretching the leather into final form. Otherwise normal wear will accomplish the stretching and over time the loops will become loose more easily.

Very nice job on the Threepersons' holster!

Edited December 26, 2009 by Lobo

[okie44]

I have not tried to build any belt loops my self, but I remember reading years ago, that a good way to keep the loops from stretching too much over time, is to cut a strip of leather and wet it, then stretch it as far as it will go. Then use it to make the loops. I don't know if this would help or not.

[Larry]

Thanks Okie44 I'll check it out. It's sure worth looking in to.

Lobo, thanks for the tip. Wet forming the loops will also help when I go to stitching them in place. Also, thanks for the compliment on the holster. Coming from you means a lot.

[goodfella]

Thanks Okie44 I'll check it out. It's sure worth looking in to.

Lobo, thanks for the tip. Wet forming the loops will also help when I go to stitching them in place. Also, thanks for the compliment on the holster. Coming from you means a lot.

here is mine actually quite smiple to make id be glad to talk to you you need further help lee

Thanks Okie44 I'll check it out. It's sure worth looking in to.

Lobo, thanks for the tip. Wet forming the loops will also help when I go to stitching them in place. Also, thanks for the compliment on the holster. Coming from you means a lot.

here is mine actually quite smiple to make id be glad to talk to you you need further help lee