Members tnawrot2 Posted October 1, 2013 Members Report Posted October 1, 2013 I have a Singer 7-33 with a Consew 3/4 horsepower 1725 RPM clutch motor. The engagement arm is very stiff going down and won't return. Is there any adjustment I can do? I can't find any instruction on the internet. It's an old motor, there is a spring on a rod with a wing nut on the end, adjustment doesn't help. Quote
Members gottaknow Posted October 1, 2013 Members Report Posted October 1, 2013 (edited) You could probably use some lube where the clutch shaft slides through the motor housing. It's common for that to get dry and sticky. Some of those motors have oil cups (like the older singers) and some don't. When I service clutches, I usually give that area a good coat of white lithium grease. I would also disconnect the pittman rod from the pedal to make sure the pedal itself isn't sticking. Regards, Eric Edited October 1, 2013 by gottaknow Quote
Members tnawrot2 Posted October 1, 2013 Author Members Report Posted October 1, 2013 Thanks Eric, I was hoping you would see this and respond. I will grease it tomorrow. Quote
Members Gregg From Keystone Sewing Posted October 1, 2013 Members Report Posted October 1, 2013 (edited) If this is a Consew 'Premier II' 3/4 HP clutch motor, I know EXACTLY the problem, and it's not what many would think; they had some damn heavy grease/glue, new out of the box, that was, well, wrong with the clutch sleeve. It would stick like glue and not allow the clutch arm to return properly. I'll get right into it, since I have done dozens of these, follow by the numbers, hope this helps. Click image to enlarge. I feel your pain, and it took me a bit of head scratching to finally figure out what was going on. This was about five years or maybe a bit more these motors were new out of the box with these problems. Hope this helps, I am pretty sure you be up and running after this fix. Edited October 1, 2013 by Gregg From Keystone Sewing Quote Industrial sewing and cutting, parts sales and service, family owned since 1977, Philadelphia, Pennsylvania USA, 215/922.6900 info@keysew.com www.keysew.com
Members tnawrot2 Posted October 1, 2013 Author Members Report Posted October 1, 2013 Greg, you are a life saver, I didn't have that exact clutch motor, but basically I followed the schematic. You are so right about the grease, I think they mixed it with glue. A wire brush wouldn't touch it, I had to take a small screwdriver and scrape it out. Replace it with white lithium grease and it works like a charm. Thanks again. Quote
Members Gregg From Keystone Sewing Posted October 1, 2013 Members Report Posted October 1, 2013 Greg, you are a life saver, I didn't have that exact clutch motor, but basically I followed the schematic. You are so right about the grease, I think they mixed it with glue. A wire brush wouldn't touch it, I had to take a small screwdriver and scrape it out. Replace it with white lithium grease and it works like a charm. Thanks again. Excellent, glad to help. Quote Industrial sewing and cutting, parts sales and service, family owned since 1977, Philadelphia, Pennsylvania USA, 215/922.6900 info@keysew.com www.keysew.com
Members gottaknow Posted October 1, 2013 Members Report Posted October 1, 2013 Even the bulletproof Amco motors eventually have this issue. Which is what I suspected was the problem. For future reference I also use the same white lithium and work a thin cost onto the cork face of the clutch disc. Make the clutch work smoother and last longer. Regards, Eric Quote
Members photopigiste Posted October 30, 2013 Members Report Posted October 30, 2013 (edited) Hi ! I have an old Juki DDL-555-4 , it was a servo auto clutch motor , the servo box is defect. and i can' t find it ,the motor is like brand new ,there is 2 rubber disks in the clutch ,i have removed all eletronics on my sewing machine ...Can i fit an ordinary clutch on this motor ? Edited October 30, 2013 by photopigiste Quote
Members Gregg From Keystone Sewing Posted October 30, 2013 Members Report Posted October 30, 2013 Yes, you can. We have ripped off dozens of motors from electronic under bed trimmer machines that were in the 30 year old range. The Juki DDL-555 was always a great model. Quote Industrial sewing and cutting, parts sales and service, family owned since 1977, Philadelphia, Pennsylvania USA, 215/922.6900 info@keysew.com www.keysew.com
Members big dave Posted December 14, 2015 Members Report Posted December 14, 2015 Very helpful thanks Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.