Members JAZZMAN Posted May 9, 2015 Members Report Posted May 9, 2015 Hi so i have been using tanners bond leather cement for my projects when i need to just hold something together until i stitch it. Now my wife bought some gorilla wood glue for a craft project and it was half the price for 4 times as much. In my opinion the leathercraft cement seems to just look and smell like pva glue anyway. So i stuck a couple of pieces of scrap together with the gorilla glue and they seem to have stuck just fine. Can anyone tell me why i should not just use the gorilla instead of the dedicated leather cement. If i was using the glue as a permenant fix i would understand why i might use leather specific glue, but when it is only until the stitches are in place i cannot see why it will not do the job just the same, unless anyone can tell me any different. I do live on a very low income and so am always looking for ways to save money on my leathercrafting, but not at the expense of making lower quality items. Quote
Troy I Posted May 9, 2015 Report Posted May 9, 2015 I use good ol ' fashion contact cement from Lowes...about $12 to $15 for a 32 ounce can...works just fine. Quote TroyImler's LeatherBentonville, VA 22610 http://www.ebay.com/usr/imlers_leather
Members zuludog Posted May 9, 2015 Members Report Posted May 9, 2015 (edited) A bit of Surfing shows:- http://www.theidentitystore.co.uk is Tandy's agency in UK, and sell Tanners Bond Cement at £29-47 per US Quart, which is 946 ml, or as near as dammit 1 litre. I have seen on YouTube a recommendation, possibly by Ian Atkinson, to use Evostick Timebond, which is a contact adhesive. Prices for this seem to vary considerably 65 g tubes are about £3-70 to £3-99, and so too expensive for a large amount 250 ml tins are mostly about £6 to £9, but I have seen them at £16 1 litre tins seem to be about £20 to £30, but Homebase are selling them for £12-99, and I think you get an over 60s discount as well, if that applies to you. But I know you are disabled, so perhaps you know someone who is old enough to do the shopping for you, with a discount, if you give them a precise order. Often a local shop will be as cheap as any, so shop around. And there will be no shipping costs. If you order by Internet/mail order, is is more than likely that Royal Mail will class it as hazardous, and so refuse to handle it. That means using another carrier, so don't forget to check the delivery/shipping/p&p costs. I use Bostik, UHU, or own brand contact or general purpose adhesive from discount stores, whichever is the cheapest, Typically they are £1 to £1-50 for a 65 g tube. When my current tube runs out, I'll get some Timebond With these or Timebond I would use small dabs of the glue, just to hold the leather in place, not to have a continuous 'run' of glue. But if you already have the Gorilla glue, and it does the job, just carry on using it. Edited May 9, 2015 by zuludog Quote
Members JAZZMAN Posted May 9, 2015 Author Members Report Posted May 9, 2015 Wow Zuludog, thank you so much for taking the time to give me such a well thought out and well researched response to my question, you are obviously a very giving person, i have seen a lot of your posts and they are always very informative and heartfelt and i thank you for them. I will have to see if i can indeed get a litre of evostick timebond if i can get one for £12.99, my wife is using the gorilla glue to make rocking chairs out of pegs so hopefully she will get bored of that after a bit and i can nick the rest of it from her . Thanks again zulu and take care my friend.Peace. Quote
Members zuludog Posted May 10, 2015 Members Report Posted May 10, 2015 When making knife sheaths, I tried holding the glued edges together with Bulldog clips, but even though I padded them with scrap leather they left marks & impressions on the 'proper' leather. If you look at Nigel Armitage's video on YouTube - How To Make A Simple Hand Made Wallet - you'll see that after he has glued, he uses a screw press. Well I don't need anything that grand or expensive.Now I lay the work on the bench, then place a piece of wood on top followed by my toolbox. But as Nigel shows, I pad underneath and on top. He uses leather but I use 3 thicknesses of old, much washed white T shirt fabric each side kept just for that purpose. Rocking chairs out of pegs? Presumably they're models? Quote
Members zuludog Posted May 10, 2015 Members Report Posted May 10, 2015 1 litre of glue is a lot of glue. Why not try a tube of Timebond first, to see if you like it. Alright, £3-75 or so is expensive for 65 ml, but it's cheaper than spending £13 or more, and you would only need to do it once. Or shop around to see if you can find 250 ml for £6, which would be a reasonable compromise. PVA glue is usually used for wood, but might be OK for leather as it's only being used to hold the leather together for sewing, and it's cheaper than the others. Again, why not get a small amount to try? It can be used on paper, card, and wood, so if you don't like it for leather you or your wife could use it for other things. Should be easily available at DIY stores. Quote
Members TinkerTailor Posted May 10, 2015 Members Report Posted May 10, 2015 I use 3 thicknesses of old, much washed white T shirt fabric each side kept just for that purpose. I used to do this, then i noticed i had imprinted the texture of the cotton fabric onto still slightly damp leather. I fixed it by re-casing the leather, and pressing it again using the smooth plastic from a pastry box lid from the bakery, instead of the fabric. I got some dedicated leather chunks for this now. I cut them out of an old leather jacket from the thrift store, cleaned and resolened them, to eliminate any potential dye transfer. Quote "If nobody shares what they know, we will eventually all know nothing." "There is no adventure in letting fear and common sense be your guide"
Members JAZZMAN Posted May 10, 2015 Author Members Report Posted May 10, 2015 Rocking chairs out of pegs? Presumably they're models? LOL. yes zulu they are models, i hope she does mean models anyway or else we are going to need dustbin sized containers of glue. Sorry for not making that clear.I will post a picture of one when she has made one. Quote
Boriqua Posted May 10, 2015 Report Posted May 10, 2015 Gorilla glue expands and can come out of your seams if you are not careful. It is also a very stiff kind of foam when dry. May not matter in some areas but that is your call. If you stick two piece together it will be very stiff. Regular old contact cement from the hardware store is cheap and remains flexible. I LOVE gorilla glue for wood but I wouldnt use it for leather Quote
Members JAZZMAN Posted May 10, 2015 Author Members Report Posted May 10, 2015 (edited) Thank you Boriqua,as i said in my original post i am all for saving money but not if it might cause me problems or a poor quality project, because i like to make bags(well i am only on my second one so far) with curved gussets i think i need to get some contact cement as this seems to be the most common glue everyone seems to advise, so thank you all for helping me with this. This forum is fantastic Edited May 10, 2015 by JAZZMAN Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.