Jordanball33 Report post Posted March 12, 2017 Can anyone post pictures of how your speed reducer is installed under your table. There isn't much room and wanted to get some ideas about the best way to go about it. I have a juki 1541s if that matters. Quote Share this post Link to post Share on other sites
mikesc Report post Posted March 12, 2017 How to install your speed reducer, will depend on what your speed reducer looks like, posting a photo of it will make any replies/advice much easier. Quote Share this post Link to post Share on other sites
JimTimber Report post Posted March 12, 2017 Easiest way to do it is placing the reducer where the motor started, and then moving the motor to a new location. Original belt goes to the reducer, new belt will be decided on where the motor winds up. If you need to switch sides of belt for access, you can reverse the motor in the controller parameters. Quote Share this post Link to post Share on other sites
Jordanball33 Report post Posted March 12, 2017 Above is my machine. Here's pulley Ok will not let me show another photo yet. I will try and upload to imgur Quote Share this post Link to post Share on other sites
Jordanball33 Report post Posted March 12, 2017 Quote Share this post Link to post Share on other sites
JimTimber Report post Posted March 12, 2017 If you don't have room to go backwards, you could mount another cross brace to the legs and go down. Quote Share this post Link to post Share on other sites
mikesc Report post Posted March 13, 2017 (edited) copy and paste this following line ( exactly like it is ) into google site:leatherworker.net mounting speed reducer the results will be all the threads that are here on leatherworker.net about mounting speed reducers, many have photos of "how to" mount speed reducers like yours under flatbed machines like yours ( you have servo motor, some of the photos are of clutch motors and speed reducers, but the positioning is virtually the same, give or take a few millimetres ) ..the first two threads on those results will explain how to mount it..with photos.. http://leatherworker.net/forum/topic/8927-speed-reducer/ and this thread http://leatherworker.net/forum/topic/51826-adding-a-speed-reducer-to-a-flatbed/ HTH Edited March 13, 2017 by mikesc Quote Share this post Link to post Share on other sites
mikesc Report post Posted March 13, 2017 Btw..using Google ( or Bing or whatever search engine ) like that to find what might be on a site works for any subject and any site.. this part ( with the full colon )like so site: tells the search engine to only look on a particular site next comes the name of the site ( could use any site name that you want to search ) in this case leatherworker.net and lastly ( after leaving a space between it and the name of the site ) comes what you are looking for mounting speed reducer put it all together site:leatherworker.net mounting speed reducer and voila ! I also ran ( for curiosity ).. site:leatherworker.net raccoons and got a whole bunch of threads from here with the word raccoons in them ..who'd a thunk it .. Quote Share this post Link to post Share on other sites
Yetibelle Report post Posted March 13, 2017 I suspect you have the room to mount it like this? Quote Share this post Link to post Share on other sites
Gregspitz Report post Posted March 13, 2017 Speed reducer I installed went directly in line with the machine and I just had to move the servo motor a little Quote Share this post Link to post Share on other sites
Jordanball33 Report post Posted March 14, 2017 Got into installed. Once I figured out how I wanted to do it. (With advice from a friend) I cut off one ear for clearance and mounted it in less than 10 minutes. She is super slow stitching now. I love it. I'll upload a few photos. Thanks for the help Quote Share this post Link to post Share on other sites
Jordanball33 Report post Posted March 14, 2017 Quote Share this post Link to post Share on other sites
JimTimber Report post Posted March 14, 2017 9 minutes ago, Jordanball33 said: Got into installed. Once I figured out how I wanted to do it. (With advice from a friend) I cut off one ear for clearance and mounted it in less than 10 minutes. She is super slow stitching now. I love it. I'll upload a few photos. Thanks for the help Call it the Van Gogh mod. :D Quote Share this post Link to post Share on other sites
Gregspitz Report post Posted March 14, 2017 do you mean you enlarged the slit for the belts?? that is what I had to do.. Quote Share this post Link to post Share on other sites
Jordanball33 Report post Posted March 14, 2017 No. I cut the bracket that bolts the 3 bolts to the bottom of the table. You can see it in my 3rd picture Quote Share this post Link to post Share on other sites
Jordanball33 Report post Posted March 14, 2017 Here's a video of me sewing with it. Quote Share this post Link to post Share on other sites
Yetibelle Report post Posted March 14, 2017 NICE work! Quote Share this post Link to post Share on other sites
suzelle Report post Posted March 24, 2017 Thanks for sharing this, very helpful! Quote Share this post Link to post Share on other sites
