calanneh Report post Posted January 8, 2009 I have some 3-4oz vegtan I am making into wristbands and chokers but the backs are kinda fuzzy. They are a bit too thin to skive without risk of cutting too much. Whats the next best way to make the back look better? I have trimmed it with scissors and then 'painted' some with Gum Tag and that helped, but there are some pieces that are just too hairy...... What yall think?? William Quote Share this post Link to post Share on other sites
ferret Report post Posted January 8, 2009 You could try an electric shaver, if that doesn't work use 1oz goat as a liner. Quote Share this post Link to post Share on other sites
BarryKing Report post Posted January 9, 2009 Use a sander with 150 grit or so. This will take the fuzz off and still allow you to rub it smooth. Just the vibrating wood type sander works great. If it is really fuzzy, you may have to use coarser paper, as the finer will clog up faster. A belt sander ends up leaving streaking, similiar to a wood grain look. Try it on a scrap piece first, but it has worked for me several times. Barry Quote Share this post Link to post Share on other sites
Knife Knut Report post Posted April 13, 2010 Just throwing this out there as a possibility: What about one of those sweater shaver things? Or, maybe a blowtorch set on low flame to scorch the fuzzies off, sort of like scorching off pinfeathers. Quote Share this post Link to post Share on other sites
BustedThumb Report post Posted April 14, 2010 (edited) I used packaging tape to keep it from warping while tooling, and while pulling it off, the adhesive half came off and pulled the rough fuzzyness up - so I was left with a sticky and really fuzzy surface. Just hand sanding in a circular motion with really coarse paper took care of it, and left a nice slightly fuzzy but buffed surface. If I'm not lining it, I plan on it now as a step. Also, when dying and finishing any non-sewn edges, I spend a little time at the end to sand out the dye spillover on the flesh side. Edited April 14, 2010 by BustedThumb Quote Share this post Link to post Share on other sites
funnygirl62221 Report post Posted April 14, 2010 I used packaging tape to keep it from warping while tooling, and while pulling it off, the adhesive half came off and pulled the rough fuzzyness up - so I was left with a sticky and really fuzzy surface. Just hand sanding in a circular motion with really coarse paper took care of it, and left a nice slightly fuzzy but buffed surface. If I'm not lining it, I plan on it now as a step. Also, when dying and finishing any non-sewn edges, I spend a little time at the end to sand out the dye spillover on the flesh side. I've had good luck with using Gum Tracanth. Just apply a liberal amount, smooth the fuzzies down and let it dry. :D Quote Share this post Link to post Share on other sites
GoldenKnight Report post Posted September 4, 2012 I've found that gum trag does not hold up well next to sweaty skin and will actually get slimy. I have had much better results with a light coating of Bag Kote and immediately slicking with a wood slicker to smooth out the fuzz. This works very well & doesn't get slimy with sweat. Quote Share this post Link to post Share on other sites
Sylvia Report post Posted September 4, 2012 (edited) I have some 3-4oz vegtan I am making into wristbands and chokers but the backs are kinda fuzzy. They are a bit too thin to skive without risk of cutting too much. Whats the next best way to make the back look better? I have trimmed it with scissors and then 'painted' some with Gum Tag and that helped, but there are some pieces that are just too hairy...... What yall think?? William Hand sanding works pretty good. 150 and 200 grit and a sanding block. Use the 150 to knock down the big bits then 200 (or finer grit) get it more like suede. Then gum trag and slick. then seal it with your favorite sealer like super sheen, wyo-shene, or Resolene. Oh gack... someone resurrected a dead thread. LOL Oh well. Edited September 4, 2012 by Sylvia Quote Share this post Link to post Share on other sites
