Second attempt at a holster

[SpaceRanger42]

If you go to Home Goods or TJ Maxx or Rosss or one of  those places, hit the kitchen aisle and grab a wooden pastry roller. they are excellent all around shaping tools for leather work and only cost about $8 in those places.  Make sure you are gluing all the way to the edge.  I always cut one piece over sized then trim the excess.  I do not recommend using wax on the edges of projects any more.  Especially on carry holsters.  As the temperature changes and the piece gets worked about and stretched while it's on your belt you will actually squeeze that wax out of the area it was filling.  Once your edges are trimmed even, wrap some fine grit sandpaper around a burnishing tool and go to work on the edges.  Likewise beauty supply stores have some really interesting very fine polishing boards and foam blocks.  You can also go old school and use a piece of broken glass to shave those edges smooth and even.  If you do that be careful or you will cut the snot out of yourself.  Also I recommend using thick bottle glass, like a coke bottle.  Once you have your edge super smooth and even apply gum tragacanth  to the edge, let it sit for a minute then go to town with your edge slicker.  Don't pound on your edges unless you have a smooth finish hammer like a cobbler's hammer.  Use a better contact cement. Barge or Dap ( same active ingredients but Barge is an import)

[Double Daddy]

The biggest thing for me on edges is like SpaceRanger42 said...make sure you apply glue (the good smellin' DAP Welwood Contact Cement in the red can, in my case) all the way out to the edge, especially where you're gonna be sanding/edging/burnishing. I tend to trend toward saddle soap for my edge "salve" after knockin' the corners off...it lets me apply dye afterwards or before (depending upon what's going on with my project or m'mood)...whereas gum trag isn't as forgiving (or as least I haven't found it to be so). Search within the LW forum for HidePounder's edge tutorial...that thread has his method and input from others on this very subject.

Might have to give one of those pastry rollers a try...or a j-frame laminate roller...Mmmm? Costs me money every time I log on here...

[Bolt Vanderhuge]

2 hours ago, DocDaddy said:

This explains a ton. I am using Fiebings leathercraft cement but I am not hammering it out and I am not weighting it down either. Thank you for the tip! 

I do none of what alpha mentioned yet I get very nice edges without a seem. The glue that you use though could cause this issue like alpha mentioned. I use Tandy's Bond contact cement and brush it until it is wet leather so there is no extra glue. After letting the glue set up I put the two panels together and run my hands over the glued area to make sure they make full contact. But I do not add weight, clamp, or hammer the panels together. After that I use a razor blade to trim any hang over of one panel over the other. I make sure that both panels are now exactly the same before moving forward. When beveling the edges I again make sure that the panels are even by running the beveler over the edge seem after beveling. After dying and burninshing I will run some 320 or 400 grit sandpaper over the edge then redye as needed. Then burnish again and then sand again if necessary. Repeat if necessary. Once satisfied I then apply my finish. When the finish is dry I burnish again. All my burnishing is by hand but I only have to spend a couple minutes each time to get good results. The prep work of making sure the panels are even and smooth really cuts down on the rest of the work.  Oh I should add that I dye my edges, I do not use edge cote.

 

This first pic here the holster is lined so it is 4 layers of leather. If you look at the flash lit area you can kind of make out one of the seems.

 

 

 

 

Edited November 20, 2017 by Bolt Vanderhuge

[SpaceRanger42]

4 hours ago, Double Daddy said:

whereas gum trag isn't as forgivin

That is totally true.  I should mention if you do use pine snot (gum trag, looks like snot smells like pine sol) make sure you dye your edges first because it totally seals the pores of the leather.

[DocDaddy]

Thank you all for the help. I knew getting involved in this forum would be good for honing my work.  I am probably going to break down and buy one of the oblong punches on payday and invest in some barge and gum trag. 

[Bolt Vanderhuge]

7 minutes ago, DocDaddy said:

Thank you all for the help. I knew getting involved in this forum would be good for honing my work.  I am probably going to break down and buy one of the oblong punches on payday and invest in some barge and gum trag. 

For punching two layers try punching your outside panel before attatching it to the inside panel. Then after they are attatched you will find it very easy to punch thru the second layer. Also the surface that you are punching on should be solid. Too much give or softness below your project will absorb some of the impact and reduce the effectiveness of your blows.

 

GumTrag is for getting fibers to lay down and stay down. It will do nothing for the seam that you are asking about. You need to get both panels to be even whether thru slicingshaving or sanding.