Phil2011 Report post Posted December 6, 2011 Hi! Here is a pair of ankle moccasins I made for my girlfriend: I used this thick, very soft and very supple full grain leather: I designed the pattern by myself, and every assembling is glued and hanstitched (two needles, with linen thread). I added a piece of stiff (but thin!) suede around the heel, inside the mocs, to prevent this area from crushing down while walking. The size is womens 5.5US (36EUR). Quote Share this post Link to post Share on other sites
Luke Hatley Report post Posted December 6, 2011 (edited) Those are some fine looking Mocks......much like the Apachie Mocks........ PS. if you could draft that Mock in patterns up to mens & ladys sizes i honest beleive you could sell the patterns......I M H O. Edited December 6, 2011 by Luke Hatley Quote Share this post Link to post Share on other sites
Phil2011 Report post Posted December 9, 2011 Thanks a lot for your comment, Luke! I feel flattered! Well, it's a very good idea and I wonder if I could do it! But I miss the knowledge to be able to draw patterns of different size from a first pattern... If you would explain, that could be great! Quote Share this post Link to post Share on other sites
Luke Hatley Report post Posted December 9, 2011 Phil i cannot do it either......I can only do one pair at a time. Quote Share this post Link to post Share on other sites
Phil2011 Report post Posted December 9, 2011 So, I wish someone who read this could tell us! I like a lot the mocs on your pic! What is the sole made of? Do you have other pics of the mocs you make? Quote Share this post Link to post Share on other sites
Suicide Report post Posted December 9, 2011 So, I wish someone who read this could tell us! I like a lot the mocs on your pic! What is the sole made of? Do you have other pics of the mocs you make? Hi guys, The easiest and _almost_ 100% working method is to draw your originall pattern in the any of graphics editor (I used either Photoshop or Illustrator - both working just fine for it) and then scale it to required size. The rough way I was proposed by someone who has experience in garment sewing was just cut sole along its "middle lines" (vertical and horisontal) - you'll get 4 pieces, then move them apart and away from the point where these lines originally crossed. You'll get sole shape scaled pretty ok this way. But problems come with the tops: you need do the same with the them. And this is something tricky as you need constantly tracking where which part is going and how far. That gal was doing such tricks for jacket/trousers pattern almost automatically, but can't suggest anything for boots/mocs. So I went on hi-tech side And in any way after scaling I would suggest to make the test boot from any of old jeans or any other fabrics which won't stretch much and try it on or at least see if everything aligned as it should. I also was told what scaling pattern down is more prefferable than scaling it up (eg you'll most likely get something awkward by scaling kid's boot patterm into adult size). Hope it helps Quote Share this post Link to post Share on other sites
Tina Report post Posted December 9, 2011 Very nice looking mocks, and they look to be verry comfy too Quote Share this post Link to post Share on other sites
Phil2011 Report post Posted December 10, 2011 Hi Suicide, thank you for this tip! Certainly it may help! Following your explanation, I went to a sports store and I took some measurements on french made jazz shoes (with padded suede sole) : I measured three pairs, in french sizes 34, 35, and 36. Here is the result: 34: 8" Long, 2 6/8 wide (on the widest part of the sole). 35: 8 3/8 L , 2 7/8 w. 36: 8 6/8 L , 3"w. As I already knew, the difference from a size to another one is more important on length than on width. Quote Share this post Link to post Share on other sites
Phil2011 Report post Posted December 10, 2011 Hi Tina, thanks a lot for your comment! Yes, my gf enjoys these mocs! She owns several pairs of slippers for home (Isotoner, ballet slippers, etc...) but she prefers these mocs! That's why I think I'll make another pair, with two-layers soles for outdoor wearing! Quote Share this post Link to post Share on other sites
carolb Report post Posted March 11, 2012 I am wondering how the heel held out with the stiffer suede put in the heel area? Do you sew or glue it in place? I made soft sole moccasin and mukluks and the sole always get smashed - something that totally frustrates me. I have 8 children and they all want a pair but I would like to solve this problem. Thanks. Hi! Here is a pair of ankle moccasins I made for my girlfriend: I used this thick, very soft and very supple full grain leather: I designed the pattern by myself, and every assembling is glued and hanstitched (two needles, with linen thread). I added a piece of stiff (but thin!) suede around the heel, inside the mocs, to prevent this area from crushing down while walking. The size is womens 5.5US (36EUR). Quote Share this post Link to post Share on other sites