Gibbsleatherworks

Just another idea to pass on: I had been using a drill like that for a slicker, I just had a wooden thread spool with a bolt running through it. It was a pain to control so I found a 1/2" chuck at home depot that attached to an electric motor I had laying around. After chucking on a large, round, hard wood drawer pull, I mounted it to the work bench. It is much easier to slick edges now because I can use both hands for control.

Err sumthin

After some needle size searches I found that the Pfaff can take up to a size 24. The other three only had up to size 22 available. Would this hint at its ability to handle larger threads?

Thanks for the replys. Im still learning about machines so Im still unsure of the thread size I will need to use. Specifically I will be building motorcycle seats, sewing two pieces of 8oz or so together at very slow speeds.

Im looking at a few head units to replace my Singer 281-1 which wont run larger threads. Im looking to use 138 or 207 thread, I already have speed reduction and a servo motor. Heres a few heads that Im looking at, hoping for some good advice. Im leaning towards the Pfaff 545 but thought that a cyclinder bed could be useful too. http://cgi.ebay.com/ws/eBayISAPI.dll?ViewI...em=180384119109 http://cgi.ebay.com/ws/eBayISAPI.dll?ViewI...em=260444538616 http://cgi.ebay.com/ws/eBayISAPI.dll?ViewI...em=260449173110 http://cgi.ebay.com/ws/eBayISAPI.dll?ViewI...em=260447415341

Great work as always David. Killer bike too. I read and commented on another discussion about black seats recently, and the same thought were passed around. Its definatly dissapointing to have to cover your art up.

Great thread, tons of great info. Im getting the fever to build a booth now. The lazy susan shown in the booth picture Kate posted is an upgrade Im doing today!

Wow, forgive me for attempting to help someone that asked for it. Thanks for chopping my legs out from under me. That was hurtful, I had assumed this was a friendly forum. Of course its always easier to find fault in someone than it is to offer a solution. And I expected more from a moderator.

Ive seen a few videos on youtube on sharpening and using the head "round" knife. sharpening sharpening cutting skiving Dont discount the box cutter with the stiff blade (not razor blade). With it cut in a couple of passes. Sharpness is essential. Theres a barbers trick to test for sharpness, rub the edge of the blade lightly and slowly over a damp thumb nail. To a barber, if it doesnt drag its not sharp enough. FWIW

If I can add something, I use the Tandy stitcher alot also for small stuff. When I used it for the first time I learned quickly that the needle isnt stiff enough to stay straight when punching the holes. I next moved to a simple ice pick that I sharpened, then used a plastic cutting board under it while pushing straight down. The plastic boards wont allow the awl to sink into it so the depth of the awl stays constant, as well as the hole diameter. A good awl like Marlon said is worth it. The handle of an true awl is surely safer to put your weight on than a simple ice pick. Someone asked about a groover...by using one, the stitch falls lower into the leather hiding very slight imperfections. Leaving a slightly cleaner looking stitch. It also protects the thread from abrasion and wear.

Ive also used 3M for linings in phone cases, holsters. Seems to work well. Like JustWakingUp said, be careful to not over apply and allow it to slightly dry before applying the fabric, less is more. Also protect the edges of the leather when spraying, its hard to remove the adhesive overspray. Try it on a sample to practice the amount of adhesive and the timing of applying the fabric. Barge's adhesive can be brushed on to offer better control.

Ive seen that tattoo flash before, always thought it would make a good seat, and it did! Great job. You got that eco flo antique to look good, thats tough to do.

Very cool, I dig it.

I had planned on using an old electric motor to mount a wooden burnisher on. Adding a round strope to the top of it would work the same way as your disk sander. Genious idea, thanks.