Search the Community

Hey all, I’m working on a banjo strap and I’m at the stage where I’ve added RTC Sheridan resist over the carved and stamped design before applying the antique gel. However, after applying and drying overnight, the RTC is drying pink and splotchy around the edges on the white acrylic paint, and it’s feeling sticky on those spots compared to everywhere else. Now it’s picking up a lot of dust and debris that’s nearly impossible to wipe off. I’ve now stripped and repainted those spot three times, trying very carefully to avoid the edges of the dyed leather around it so it doesn’t pull color, but I woke up this morning to the same results that I’ve been experiencing. This is my first project using RTC as I’ve seen it highly recommended as a resist for antiquing over acrylic. I’ve diluted it with just a little bit of water and I’m applying two coats with a brush only on the carved and painted areas, avoiding the dyed background leather because I don’t want the sheen there. I can’t seem to upload pictures because the files are too big, so hopefully my description comes across! I appreciate any suggestions.

Hey all, I’m working on a banjo strap and I’m at the stage where I’ve added RTC Sheridan resist over the carved and stamped design before applying the antique gel. However, after applying and drying overnight, the RTC is drying pink and splotchy around the edges on the white acrylic paint, and it’s feeling sticky on those spots compared to everywhere else. Now it’s picking up a lot of dust and debris that’s nearly impossible to wipe off. I’ve now stripped and repainted those spot three times, trying very carefully to avoid the edges of the dyed leather around it so it doesn’t pull color, but I woke up this morning to the same results that I’ve been experiencing. This is my first project using RTC as I’ve seen it highly recommended as a resist for antiquing over acrylic. I’ve diluted it with just a little bit of water and I’m applying two coats with a brush only on the carved and painted areas, avoiding the dyed background leather because I don’t want the sheen there. I can’t seem to upload pictures because the files are too big, so hopefully my description comes across! I appreciate any suggestions.

Hello, I was wondering if it is possible to dip leather into RTC Resist and Finish? If so, is there a good technique to get it to come out right? Or is it better to just brush on with a wool dauber? Thanks!

Hello, Is there much difference in RTC by Sheridan being used as a finish compared to Bee Natural Leather Finish in terms of feel, durability, color transfer/fading, cracking or waterproofing that you guys have noticed. I like both products but wanted to get your feedback on if one is better than the other in the long run. Thanks!! Stuart

I am building a picture frame using 4 straps laced together at the 45 degree corners. I tooled in an arrowhead design using a basketweave tool. I wanted to use an antique finish so I started with two practice straps before moving to the actual project. After tooling I conditioned the practice strips with Fiebing’s Neatsfoot Oil Compound which immediately darkened the leather. After an overnight dry I followed the directions on the Bee Natural RTC bottle for antiquing. I applied another coat of Neatsfoot oil, I didn’t have any Leathercare #1 Saddle Oil, let it set for 3 hours followed by a coat of RTC as a resist on ½ of each practice strap, let it dry for one hour and applied Fiebing’s Antique Finish; Medium Brown on one strap and Mahogany on the other. The finish immediately combined with the RTC and uniformly stained the leather. There was no resisting on the raised areas and no amount of buffing could bring the stain off. I could not tell where I had applied the RTC compared to the area with no treatment. This was not the look I wanted so after reading some of the other posts I modified the sequence on the actual straps used for the project. I wanted to keep the leather as natural as possible before antiquing so after tooling I treated the 4 straps with Bickmore Bick 4 as it is the only conditioner I have found that will not darken the leather. The problem with Bick 4 is that it goes on like lotion and builds up a residue in the deeply tooled areas. After drying I had to take a brush to remove the residue. The second coat of Bick 4 soaked in much better and left very little residue. As I had read on other posts, I applied the RTC and allowed it to dry overnight. RTC is very watery and soaks into the deep cuts as well as the raised areas. I applied a second coat of RTC and allowed it to dry for 2 days. I applied the Antique Finish which seemed to work as it should until removing the finish from the raised areas. As I wiped the finish off, the RTC also came off in some of the raised areas. It peeled off the leather in thin sheets just like sunburned skin. I got the antique look but it looks old and weathered with still too much staining on the raised areas. It looks more like a bad job of staining than a good job of antiquing. Has anyone else had similar problems with RTC?