Jump to content

Recommended Posts

  • Members
Posted

Great lookin' holster! The stitching looks well executed and the overall appearance is very attractive. How well does the sweatguard hold up? I've always doubled up on the back side because I'm afraid one layer of leather will start to deform and curl over time.

I think what really grabs my attention is the well designed tunneled loop on the back. Now, how exactly do you do that?

  • Members
Posted

Thanks LeatherCaptain! I'm actually in the middle of stitching one up right now that has a reinforced sweat shield. I'm not sure it's really necessary for OWB carry, but thought I'd give it a try. At some point I'd like to start lining my holsters, which is why this particular holster wasn't reinforced - the pattern would eventually be lined, effectively helping to reinforce the sweat shield.

Regarding the belt loop, I simply designed the holster with a heavy sheet of paper, cut the pattern out, then folded it around my pistol. Then start sketching out the reinforcement piece and carry it along to the back of the holster and draw in the belt loop tunnel. Make sure the tunnel aligns with your belt slot. Once you've gotten your pattern pretty well defined, build it out of scrap leather.

I've actually built this particular pattern 3 times now. The first time (Saddle Tan in a previous post of mine) exposed a few design flaws with my lines - stitches were exposed to excessive wear at the trigger guard area, the sweat guard was too high and wrapped around the front too far, and I didn't like the stitch line around the bottom of the slide (tried to mimic one of my favorite makers, but the stitch lines work better for his overall design than they did with mine). I revised my pattern to go around the trigger guard, shortened the sweat guard and shortened the area around the end of the barrel, then built this black one. Now I'm on my third (still under construction), where I've tweaked the stitch line around the bottom of the slide, added a reinforced sweat shield, and dyed it before assembly to keep the thread natural.

My next holster will likely be tweaked again - I'll likely play around with the reinforcement piece a bit, but haven't really decided how yet.

  • Members
Posted

That's your best one yet.

It's nice when you can work on the same holster/gun combination over and over. You really get a chance to tweak the design, and you get a good feel for how to bone the holster better. After you get the design where you want aesthetically, be sure to put them to some real world use. Try carrying for long periods of time and making some road trips, and try doing a lot of defensive draws, both moving and stationary. That will help you recognize whether the design needs further refinement, and it will help you see how well the design and the construction method holds up to abuse.

Keep up the good work.

  • Members
Posted

Thanks Boomstick! My Boss should arrive today so I can finally start machine stitching! Wohoo! You're right - wearing them is extremely important. I admit, I am guilty of falling back on my daily-carry, which is a Kahr P9. It's just so small and light. Plus, my holster for the Kahr is IWB. I don't really have the proper cover garments to wear my 1911 OWB. The times I've worn this design around the house though, it was very comfortable (aside from the time I sat down and snagged the bottom of the holster on an arm rest and the beavertail rearranged my ribs... And you're right - it's been very educational to stick with one platform to learn with. It's allowed me time to focus on boning without the worry of learning the shape of a new gun. Thanks for the compliments - it's been a fun experience! I still need to see if there is a way to pull the gun in tighter to my body - but I think a lot of my problem is I simply don't like tightening my belt very tight. The curse of a desk job.

Posted

Incredible job! Man, I'm lovin' that!

"Don't squat with your spurs on."

www.GibsonLeather.com

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...