Holster Clip Source

[GuardianConcealment]

I am looking for a good source for smaller quantities of holster clips for my IWB hybrid holsters.

Black oxide, 1 /34 inside, around 1 inch wide.

I purchased a hundred from JRM clips out of NJ and they were OK. The black oxide finish was a bit inconsistent.

Looking to spend less than 50 cents per clip and would order a few hundred.

Also might consider having a custom clip made / sourced.

attached is a clip example....it is a 2030 from JRM in black

better pics are on my website: www.guardianconcealment.com

Any advice would be great.

Thanks,

James

[SOB Holsters]

looking at the photos its hard to say if the ones I use are any better, and they definitely don't come at .50c, (trust me, I wish) but they are sturdy and they do the job. KnifeKits.com carries them and charges 1.60 each if you order 10 or more. http://www.knifekits.com/vcom/product_info.php?cPath=41_56_407&products_id=1486 They don't fit well over the Kydex reinforced belts I make though. Too tight for the thickness of belt. so I just make the clips that Velcro to the back of the belt if I sell a belt as well. Two things to watch for with these clips: 1.They don't have rounded edges. Its not that they are sharp, but definitely not rounded, like ones Tandy carries (@ like 3.50 each, ouch). it could be me just being picky.. 2. if you order these, type a note in the comments section during checkout to ensure the clips are "straight". I have had numerous ones that are bowed, and/or the outer portion of the clip is not in line with the back, and it looks like crap. But since I started leaving a note, they have complied. Hope this helps!

Your leather quality looks good, what cut is it and where do you get it?

[Leatherman87]

Try bluegunstore.com 100 at $1 per

[RMB Custom Leather]

We just got some in with powder coated finish which helps with the sharp edges.

[billymac814]

I would second Robs at the blue gun store. They are better quality than ones you get for .50 cents.

I'd rather spend 1.00 or even 2.00 from Tandy and have a good quality clip than get one for .50 cents and it loses its "spring" in a year and fails on your customer. In the customers mind they are YOUR clip and when it fails they'll want you to replace it( which you should) or worse yet they won't even tell you but they will tell everyone else that the holster they bought has generic clips that don't last.

I've used every clip out there for a while and for some of that time I didn't really notice a difference other than price as they looked nearly identical, then I had several failures all at once and I tracked it down to the cheap clip. If you replace it, now you're up to the cost of a good clip anyway, if you don't or they don't tell you, how much does an un satisfied customer cost you?

Pass the cost on to your customer. They will gladly pay an extra 2 bucks for a quality clip.

[SOB Holsters]

Amen to that. Got on the site and its showing sales are suspended due to backlog. Rob, what are the cost of the clips? Also, are they a gloss finish? The last set of glossy clips I got squeaked terribly against the leather. The matte finish ones I currently use do not.

[billymac814]

Where did you see that sales are suspended? On Robs site?

Amen to that. Got on the site and its showing sales are suspended due to backlog. Rob, what are the cost of the clips? Also, are they a gloss finish? The last set of glossy clips I got squeaked terribly against the leather. The matte finish ones I currently use do not.

[Tree Reaper]

Anyone offering a 1 1/4" belt clip?

[raysouth]

Might take a look at catalog from Ohio Travel Bag. Plenty of good things there.

Ray

[RMB Custom Leather]

Guys you went to my leather store here is the supply site www.bluegunstore.com

Edited February 23, 2013 by RMB Custom Leather