Fiebings Oil Dye - Totally Uneaven - Why? :-(

[Pennypower]

Hi everyone!

My dyeing skills are kind of hit or miss, so on this belt I thought SURELY if I dip dye it, it will be even enough right? Does anybody know why it looks like this?

This picture is taken a few hours later, so it's not totally dry yet, but I would be shocked if all of a sudden it was even once it's dry. Shocked but happy!

Also, it seems to have like a greenish shimmeryness to it, in blotches. Not sure what that is either.

Oh and I dip dyed it in Fiebings Oil Dye, saddle tan :-D

Thank ya'll for your help!

[Pennypower]

The only thing I did to it before I dyed it was sand the edges and buff the surface with water :-) So there is no soup or oil on it, at least not from me. Could it have just been too dirty? Do I need to clean with saddle soap before I dye it?

Oh and one more question....if I use an airbrush, will that control the unevenness entirely? Because this is dip dyed so I'm under the impression that the problem is with the leather it'self. But I've never tried airbrushing so I don't know.

[Dwight]

Well, for starters, . . . you picked the one Feibings oil dye that I will probably never use again myself when my bottle is done.

But, . . . you might just allow it to dry thoroughly and it will be OK, . . . it has done things like that to me.

What are you using for the finish coat?

Resolene has a habit of helping to smooth out what would otherwise look kinda blotchy for me. I use it almost exclusively on belts.

Best wishes, may God bless,

Dwight

[Pennypower]

Dwight, I've been using clean lac, or clear lac, or whatever that's called LOL.

I like how shiny it makes it but sometimes it cracks. I'll try Resolene. Is there a certain brand I should get, or is that the brand?

Oh I see, Fiebings resolene.

[CanadianGirl]

Mix it 50/50 with water and use sparingly. I usually do two or so coats of it.

[Dwight]

Like Canadian Girl said, . . . mix 50/50 with water.

I use a cheap bristle brush, . . . put a good wet coat on the belt (always start with the back), . . . and keep adding and brushing until I build up almost a bubbly lather.

I then turn it over and do the same thing for the front.

Come back to the back, . . . add a little more, . . . brush the bubbles left, right, up, down, crossways, . . . until they have been brushed out.

Turn it over and do the same for the front, . . .

Hang it up on a hook and very carefully make sure wherever I have touched it that it gets a good brushing of Resolene, . . . especially the edges.

You really do want a plastic, or latex glove on the "handling" hand. That stuff won't hurt you, I don't think, . . . but it's sticky nasty, . . . kinda like a 1 year old handing you her sucker,..........

You also want to be sure to do all the bending necessary (buckle end especially) because when this hardens and dries, it can crack. Do the bending while it is still wet, . . . then touch up where you touched it bending it.

May God bless,

Dwight

[Pennypower]

THank you! I just checked it recently and it seems to have evened out a lot as it has dried more. I'm kind of shocked that it was that obvious and easy :-P

[Cyberthrasher]

You'll solve some of those problems by putting a light coat of oil on first. It helps to pull the dye in more evenly. Basically what's going on is that certain parts of the leather are dryer than others, so they suck in the dye a lot faster, where those that have some moisture in them don't - leaving those dark spots until it settles.

For your green - it's not just saddle tan. All of the browns have green in the mixture. Think of when you were a kid and mixed your colors. When you decided you were really fancy and mixed all those pretty colors and it ended up looking like poop - that's how they make brown. It's got more green in it than anything else. I have a bottle of Walnut that's horrible about it. That bottle, I apply light thinned coats and buff buff buff with a little bit of oil to settle it down. Sometimes the mix is just a little off and it comes through like that.

You will see a much more even application with an airbrush due to the way it atomizes the color and doesn't build up in any one spot more than the others. The downside is that you have to work a little harder to get the dye to penetrate into the leather deeper like it does when using a dauber or brush. That's best accomplished by applying a light coat of oil and then putting on your first coat of dye reduced by 50%. If it's already a 50/50 color, reduce it to 25/75 for that first coat. Then go through a second coat with your intended mixture.

[Pennypower]

Cyberthrasher....awesome. That makes a lot of sense. I'm going to oil first from now on.

I can't wait to get an airbrush!

[Yetiusmc]

Pennypower,

If you have a Harbor Freight close by, they have air brushes super cheap. They work generally the same as ones that will cost 4 times as much, so it may be worth it for you to learn on before you decide you like the air brush method. Good luck!