Jump to content

Recommended Posts

  • Members
Posted (edited)

I would not buy the 206 for $800 - maybe $500-$600 but not more because you for sure will end up with installing a servo motor for approx $150 and since the paint on the flat bad is worn of it has seen extensive use. But that does not mean the machine is worn off.

Advantage of the Consew 206 is that you can load the bobbin from the top (horizontal hook). This is (for me) by far more comfortable that tilting back the machine all the time when you wan to change the bobbin. And if I remember correctly the horizontal hook machines can handle thicker thread than the vertical hook machines.

Personally I would buy the Consew + new servo motor if the price is right.

Edited by Constabulary

~ Keep "OLD CAST IRON" alive - it´s worth it ~

Machines in use: - Singer 111G156 - Singer 307G2 - Singer 29K71 - Singer 212G141 - Singer 45D91 - Singer 132K6 - Singer 108W20 - Singer 51WSV2 - Singer 143W2

  • Moderator
Posted

Ollie, the price you saw for a P1206 is a little high, especially if it is in a box and needs to be fully assembled and adjusted. One of our member dealers offers brand new Consew P1206RB machines, fully setup with a servo motor, adjusted and sewn off, shipped on a pallet, for just under a thousand dollars.They also carry new 206RB-5 machines, also complete, for about thirteen hundred. Others may also carry these machines at similar prices..

Posted IMHO, by Wiz

My current crop of sewing machines:

Cowboy CB4500, Singer 107w3, Singer 139w109, Singer 168G101, Singer 29k71, Singer 31-15, Singer 111w103, Singer 211G156, Adler 30-7 on power stand, Techsew 2700, Fortuna power skiver and a Pfaff 4 thread 2 needle serger.

  • Members
Posted

Olie, your friends machine seems to be a Consew 226 not a 206

~ Keep "OLD CAST IRON" alive - it´s worth it ~

Machines in use: - Singer 111G156 - Singer 307G2 - Singer 29K71 - Singer 212G141 - Singer 45D91 - Singer 132K6 - Singer 108W20 - Singer 51WSV2 - Singer 143W2

  • Members
Posted

Constabulary I have two issues with your post.

1/ Why would you lift up a machine to change the bobbin? On a vertical shuttle machine you just reach in and pull the bobbin case out.

2/ I here all sorts of opinions about the differences between vertical and horizontal shuttles but they are generally both rated for a maximum of M20. The advantage of a vertical, replaceable bobbin case is that it is a lot cheaper to replace when it wears - particularly if you try to push through heavier bonded nylon threads.

 

 

Posted

I'm wondering if there isn't some confusion ( there certainly used to be in my mind ;-)) about what is meant by "vertical" and "horizontal" bobbin..neither term seems to refer to the actual way the bobbin "sits" or "lays".."vertical bobbins" lay on their back..( parallel to the machine bed and the surface of the planet *) which to any rational person would make them actually horizontal ( when you lay on your back are you vertical or horizontal in relation to your bed or the surface of the planet )..and "horizontal bobbins" stand on their side ( at 90 degrees to the machine bed and the surface of the planet *) which would ( again to any rational person ) make them actually vertical ..

The axis of the horizontal bobbin ( which can be accessed by sliding a plate on the bed ) is vertical in relation to the machine bed..and the axis of a vertical bobbin ( which can usually be easily reached by putting one's hand under the bench ( at least on my juki490 it can, without tilting the machine back ) is horizontal..To my "logical mind" the bobbin on my Juki 490 is actually "vertical" ( it is standing up ), wheras the bobbin on my singer 211 is actually "horizontal"..( it is lying down )..To my artistic/designers mind..it is all relative ;-)..

I now view the sewing machine "terms" ( and the fact that thread sizes get bigger in some systems and smaller in others as they increase in thickness ) as like those of French grammar..<= arcane and weird and usually inconsistent..but they are what I have to deal with.. :)

"Don't you know that women are the only works of Art" .. ( Don Henley and "some French painter in a field" )

  • Moderator
Posted

Mikesc;

Terms were developed by the manufacturers and are standardized. It may seem backwards to us users, but dealers, importers and parts suppliers use these descriptions in common to avoid confusion. You are free to personally refer to the axis of the bobbin any way you wish. But, if you contact a dealer, or replacement parts supplier and they ask whether your machine has a vertical of horizontal bobbin, use the manufacturer's designation. Otherwise, you may get the wrong parts.

To clarify, using manufacturer's designations, the horizontal and vertical axis's refer to the position of the final shaft that drives the shuttle in which the bobbin resides. If that shaft runs lengthwise under the body and the shuttle and driver is connected to the left end and sits under the bed, or inside the cylinder arm of the machine, it is a Horizontal Axis bobbin system. If the drive mechanism uses gears to drive a shaft at a right angle, coming straight up to drive the shuttle and the bobbin is dropped in from the top, it is a Vertical Axis machine. The axis of the drive shaft for the shuttle is the deciding factor.

Posted IMHO, by Wiz

My current crop of sewing machines:

Cowboy CB4500, Singer 107w3, Singer 139w109, Singer 168G101, Singer 29k71, Singer 31-15, Singer 111w103, Singer 211G156, Adler 30-7 on power stand, Techsew 2700, Fortuna power skiver and a Pfaff 4 thread 2 needle serger.

Posted

Like I said..I know what the correct terms are..but when one begins.those two are illogical.."they" say "horizontal bobbin" or "vertical bobbin"..whereas they would be far more descriptive ( and accurate ) if they said horizontal axis / or horizontally driven bobbin, and, vertical axis / or vertically driven bobbin..kind of like car engines which most people refer to as "in the front" or "in the rear"..whereas the accurate description would also include the words transversal mounting or longitudinal mounting..

BTW..here ( France ) all sewing machines are referred to as a "Piqueuse" ( pronounced pickurz )..and are "simple entrainement",( bottom feed ) "double entrainement" ( top and bottom feed ) and "triple entrainement" ( walking foot , compound feed ) ..most sewers ( pro or not ) and most dealers , don't specify which of the three they are talking about, even in their small ads / advertising .."jump foot" and other "exotics" all get lumped in with "triple entrainement"..wastes a lot of one's time when buying ( visiting machines which are not as described ) and makes ordering spares a nightmare, so I order everything, except needles from outside of France..Thus also saving myself having the prices of spares multiplied by 3 or more by the French dealers..
eg; a small bobbin for a 29K51 is over $250.oo here !! Hirose hooks start at around $500.oo..and new machines if bought from French dealers are 2 times the UK or German price, ( both countries have around the same VAT rate as we do ) and 3 times the US price.

"Don't you know that women are the only works of Art" .. ( Don Henley and "some French painter in a field" )

Posted

Btw..I'd add that although there are fora here ( in French obviously ;-) which are frequented by pro sewers and pro leather workers, I have never seen any evidence at all of any French sewing machine dealers, or spare parts dealers, jumping in to offer help or advice like the dealers do on this forum..Here nless you have cash in your hand they offer no advice, and once the machine is out the door they go deaf..This place , Leatherworker.net, is a real breath of fresh air and a goldmine for anyone who can read English, thanks to all the pros and the dealers who post here :)

"Don't you know that women are the only works of Art" .. ( Don Henley and "some French painter in a field" )

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...