Rossr Report post Posted November 24, 2017 Folks, I have up for sale a rotary strap punch. Looks similar to R-74 Randall has on their site. However I can not find any name on it anywhere so I do not know the brand. This is a solid machine. I tested a couple straps through it seems to punch just fine and move the strap forward. Has one punch in it measures 5.5mm or about 3/16in approximate. The picture of the strap shows the largest and smallest settings you can set it at to make the holes different distances. There are several settings in between. The jaws open wide enough to accommodate a four inch strap on the large side. Any questions please ask I will do my best to answer. Asking $1250 plus shipping. 6% Sales tax added if in PA. Machine is located in PA. Ross Share this post Link to post Share on other sites
steadybrook Report post Posted November 24, 2017 Can the punch be changed to accommodate different sizes? Share this post Link to post Share on other sites
Rossr Report post Posted November 25, 2017 29 minutes ago, steadybrook said: Can the punch be changed to accommodate different sizes? Yes the in the one picture on the side you can see a screw(first set of pictures under the strap on the right picture) That screw is what holds the punch in, here is a picture The tube at the top is around 8mm diameter . Weaver sells other sizes but I do not know if they punches they have will fit as it doesnt list sizes other than the hole punch size. Randall also sells them but I also do not know the tube size. Regardless though you can switch them out. I just only have one in it is all. Just to be clear while I did test the machine I am selling it as is......I dont think there are any issues but please ask me questions I will happily respond. Thanks Ross Share this post Link to post Share on other sites
steadybrook Report post Posted November 25, 2017 Ok thanks, I need one with different sized cutters included. Share this post Link to post Share on other sites
Rossr Report post Posted November 25, 2017 43 minutes ago, steadybrook said: Ok thanks, I need one with different sized cutters included. I sent you a PM. Ross Share this post Link to post Share on other sites
Rossr Report post Posted November 29, 2017 For anyone interested I ordered a few punches from Campbell Randall today. The shank measurements and length measure out the same. I will update once I get them but it appears they fit this machine. Ross Share this post Link to post Share on other sites
Rossr Report post Posted December 2, 2017 On 11/24/2017 at 6:37 PM, steadybrook said: Can the punch be changed to accommodate different sizes? I have ordered three different size punches from Campbell Randall, They do fit this machine and work just fine. Here is the list from them of what they have. While I am selling it with just the one punch in the machine. You can order any size you want from them. Hope this helps Ross R74-4.0316 - 2mm Punch For R-74 - $11.25 R74-4.0317 - 2.5mm Punch For R-74 - $13.50 R74-4.0318 - 3mm Punch For R-74 - $11.88 R74-4.0319 - 3.5mm Punch For R-74 - $13.50 R74-4.0320 - 4mm Punch For R-74 - $10.00 R74-4.0321 - 4.5mm Punch For R-74 - $14.50 R74-4.0322 - 5mm Punch For R-74 - $12.87 R74-4.0323 - 5.5mm Punch For R-74 - $15.00 R74-4.0324 - 6mm Punch For R-74 - $13.86 R74-4.0325T - 7mm Punch For R-74 - $21.25 R74-4.0325-4.7x3 - Oval Punch for R-74 - 3/16" x 1/8" (4.7 x 3mm) - $40.00 R74-4.0325-5.5x3.9 - Oval Punch for R-74 - 7/32" x 5/32" (5.5 x 3.9mm) - $40.00 R74-4.0326-4x10 - Slot Punch for R-74 - 5/32" x 3/8" (4 x 10mm) - $62.50 R74-4.0327-3 - 3mm Hole & Blade Punch (button hole) for R74 - $55.00 Share this post Link to post Share on other sites
steadybrook Report post Posted December 3, 2017 Thanks , how old is the machine? Share this post Link to post Share on other sites
Rossr Report post Posted December 4, 2017 3 hours ago, steadybrook said: Thanks , how old is the machine? I dont know as I bought it used myself. It appears to be in good shape at least to me.. Share this post Link to post Share on other sites
steadybrook Report post Posted December 6, 2017 How much does it weigh? What is the height , width , length? Also need your zip code. Can you ship it to Canada? Share this post Link to post Share on other sites
Rossr Report post Posted December 6, 2017 Machines weighs around 24 lbs. But i would want to box it up well board on the bottom to help stabilize and protect it etc so it would come out more than that for sure. Left to right it is 7 inches. Front to back 10.5 incheswithout the wheel on it. With the wheel its more in the range of 16 inches. The wheel is on with a set screw and key I could remove to ship. With the Wheel on its sits 16.5 inches high. I can look into shipping to canada I just dont know if that makes it cost prohibitive and if there is any customs issues? But happy to talk to you about it. Feel free to send me a message on the forums if you want Ross Share this post Link to post Share on other sites
steadybrook Report post Posted December 6, 2017 Ok thanks, here is the shipping address 303 EtterRd, Mt Uniacke, Nova Scotia, Canada , B0N1Z0 Please ,let me know the freight price. Share this post Link to post Share on other sites
Rossr Report post Posted December 7, 2017 I will check into it and let you know Ross Share this post Link to post Share on other sites
Rossr Report post Posted December 8, 2017 On 12/6/2017 at 0:32 PM, steadybrook said: Ok thanks, here is the shipping address 303 EtterRd, Mt Uniacke, Nova Scotia, Canada , B0N1Z0 Please ,let me know the freight price. Steady, I have sent you a private message about the shipping. Please check it out. YOu can find them in the top left corner of the site there is a letter emblem you click to see them, just in case you werent aware. Ross Share this post Link to post Share on other sites
steadybrook Report post Posted December 14, 2017 Looks like I will have to pass this machine up, too many border issues, thanks for you patience and help. Share this post Link to post Share on other sites
Rossr Report post Posted January 9, 2018 On 12/14/2017 at 6:55 PM, steadybrook said: Looks like I will have to pass this machine up, too many border issues, thanks for you patience and help. No worries, I just noticed your response. Best wishes in your leather working adventures. Folks, Make me an offer...time to get this one out of the shop. If you have any questions let me know, its a new year so lets get this one into a new home Ross Share this post Link to post Share on other sites
Rossr Report post Posted January 25, 2018 Folks this machine is sold. Feel free to remove or lock Thanks Ross Share this post Link to post Share on other sites
