Jump to content

Recommended Posts

  • Members
Posted (edited)

Right then,

I never really picked up the good habit of sharpening, much less polishing blades.  No sure why, just never worked it into me life.  Then I got into leather and no only did I need this wee proper skill, but have become rather good at it.  Have several methods for various blades and all goes right well.  The slight exception is the awl blade.  I only use Blanchard awls.

The normal routine is to use a Whetstone (with honing oil) firstly, then to a diamond stone.  Once I get a good edge, I then use dampened (water) sandpaper (3600, 8000 and 12000 grit) and I get a lovely polished edge that goes through leather like butter.

Been reading quite a bit about stones to be better educated.  I use a ceramic stone (3000 / 8000) for me knives and a strop for polishing.  Lately, I've been wondering if a ceramic stone would be good or better for the awl blades and completely forgo the whetstone and diamond altogether.  I read on a few websites that if one plans to polish a blade, ideally skip the diamond stone altogether. 

Me concern is how one sharpens an awl blade versus a knife blade and whether it's wise for the ceramic stone and wee awl blade.  I could easily purchase a ceramic stone to test, but don't wish to hurt either the stone or awl blade.

Thoughts?

Cheers!

Edited by HondoMan
  • Members
Posted (edited)

Nigel Armitage put out a video on how he prepares awls.  Might be helpful.

 

 

Edited by Tugadude
Added link
  • 4 months later...
  • Members
Posted

I use a ceramic fishing hook sharpener. They are V shaped and usually have several grades of grit all the way to fine which does a beautiful job of polishing.  

  • CFM
Posted (edited)

I sharpen my awls different than Nigel. I sharpen a flat on the tip and polish the sides this way i dont have to sharpen all four sides but i can just run it across a piece of 2500 grit sand paper i have glued on my hammering stone. i do this by using  one of the four edges as the tip then simply angle a bevel down to the opposite edge. I can then always see the leading edge put my finger on it and keep my holes running the same direction  I polish or reshape  the sides by holding my awl flat on the edge of the stone and use my small stone or a piece of sandpaper  wrapped or glued to a flat steel polishing it. I find its easier for me to keep the edges parallel and straight by moving the paper or stone  and keeping the awl steady, kind of like using a file on something. i dont know if i can load my picture the site is kind of jacked today and i have no attach button  on this. 

Edited by chuck123wapati
tried to add a picture, it failed.

Worked in a prison for 30 years if I aint shiny every time I comment its no big deal, I just don't wave pompoms.

“I won’t be wronged, I won’t be insulted, and I won’t be laid a hand on. I don’t do these things to other people, and I require the same from them.” THE DUKE!

  • CFM
Posted (edited)
On 7/18/2020 at 11:09 AM, chuck123wapati said:

I sharpen my awls different than Nigel. I sharpen a flat on the tip and polish the sides this way i dont have to sharpen all four sides but i can just run it across a piece of 2500 grit sand paper i have glued on my hammering stone. i do this by using  one of the four edges as the tip then simply angle a bevel down to the opposite edge. I can then always see the leading edge put my finger on it and keep my holes running the same direction  I polish or reshape  the sides by holding my awl flat on the edge of the stone and use my small stone or a piece of sandpaper  wrapped or glued to a flat steel polishing it. I find its easier for me to keep the edges parallel and straight by moving the paper or stone  and keeping the awl steady, kind of like using a file on something. i dont know if i can load my picture the site is kind of jacked today and i have no attach button  on this.  But my awls aren't shaped the same as a blanchard, if they were I would keep the point as manufactured but i would still hold the awl still and at the right angle and move the sharpening stone across the blade. 

 

awlsharp.JPG

Edited by chuck123wapati
more to add

Worked in a prison for 30 years if I aint shiny every time I comment its no big deal, I just don't wave pompoms.

“I won’t be wronged, I won’t be insulted, and I won’t be laid a hand on. I don’t do these things to other people, and I require the same from them.” THE DUKE!

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...