How to connect thread to 91k5, 91k6

[ddiuni]

Hello.
This time, I got the Singer sewing machine 91k6.
The question is I don't know how to connect the threads.
First, I connected the thread to the lower post. (I don't know if I connected it properly.)
Then I connected the thread to the upper needle bar. (When viewed from the front, the thread came out from the back to the front.)
And when I sew, only the upper thread is sewn and the lower thread is not pulled up at all.
what kind of problem...
If anyone knows how to connect the threads, please let me know.

Edited November 15, 2021 by ddiuni

[Wizcrafts]

You never mentioned passing the thread through the take-up lever. That lever is what pulls up the bobbin thread.

Can you take a small resolution picture of the thread path from the post on top, on down? We can see what you missed. But, I am fairly certain you forgot to thread through the take-up lever.

[ddiuni]

The thread is connected to the lower bar.
I wrote down the numbers in order.
Please tell me what's wrong

Edited November 15, 2021 by ddiuni

[ddiuni]

1 hour ago, Wizcrafts said:

실채기를 통해 실을 통과시키는 것에 대해 언급한 적이 없습니다. 그 레버는 밑실을 당기는 것입니다.

포스트 위에서 아래로 스레드 경로의 작은 해상도 사진을 찍을 수 있습니까? 우리는 당신이 놓친 것을 볼 수 있습니다. 그러나 나는 당신이 테이크업 레버를 통과하는 것을 잊었다고 확신합니다.

The thread is connected to the lower bar.
I wrote down the numbers in order.
Please tell me what's wrong

[ddiuni]

다시 순서대로 놓습니다. 무슨 일인지 알려주세요

[RockyAussie]

6 hours ago, ddiuni said:

Then I connected the thread to the upper needle bar. (When viewed from the front, the thread came out from the back to the front.)
And when I sew, only the upper thread is sewn and the lower thread is not pulled up at all

That is I think the first problem. The thread in the video that you have asked questions on before shows that at 40 seconds in that the thread comes from the front and goes to the back. In picture 11 above the long slot of the needle is facing the front as it should and and therefore that is the way the thread should follow down for it to be able to form a loop in the scarf on the back side of the needle. In picture 12 it shows the thread is coming as you said from the back which is wrong. XXXXXX

 

[ddiuni]

1시간 전 RockyAussie는 다음과 같이 말했습니다.

단서라고 생각합니다. 이전에 질문이 시샤하는 바가. 11에서 훌쩍 훌쩍 훌쩍 훌쩍 훌쩍 훌쩍 훌쩍 훌쩍 훌쩍 훌쩍 훌쩍 훌쩍 훌쩍 훌쩍 훌쩍 훌쩍 훌쩍 훌쩍 훌쩍 훌쩍 훌쩍 훌쩍 훌쩍 훌쩍 훌쩍 훌쩍 훌쩍 훌쩍 넘게 달려 가게되는 11 번 째 궁에서 훌쩍 훌쩍 훌쩍 훌쩍 훌쩍 넘어가는 훌쩍 훌쩍 훌쩍 훌쩍 훌훌훌훌훌훌훌훌훌훌훌훌훌훌훌훌훌훌훌훌훌훌훌훌훌훌훌훌훌훌훌훌훌훌훌훌훌훌훌훌훌훌훌훌훌 훌훌훌훌훌훌훌훌훌훌훌훌훌훌훌훌. 그림 12에서 당신이 보고 있다는 사실을 알려줍니다. 것입니다. XXXXXX

 

Number 17 is the scarf at the back.
You say to connect the thread like number 17 in the photo.
But even if I connect it like No. 17 and lower the presser foot and sew it, it is not sewing at all.

[RockyAussie]

I do not know this machine myself. This video that you may not have seen does look to be a similar type and in the comments section below it they have answered someone as to what needle type they use. You may be able to contact them.

If you could take some pictures showing the thread path in the top of the machine may help. It may also be out of timing and normally you can see this by Watching where the scarf of the needle is when the hook is passing the needle. The eye of the needle should be 1 to 2mm below where the hook is passing the needle. If this is not the case then the hook has to be adjusted around. The hook in your pictures does look very worn down.

[ddiuni]

7 hours ago, RockyAussie said:

이 기계는 저도 모릅니다. 당신이 보지 못했을 수도 있는 이 비디오는 비슷한 유형으로 보이며 그 아래의 댓글 섹션에서 그들이 사용하는 바늘 유형에 대해 누군가에게 답변했습니다. 그들에게 연락할 수도 있습니다.

기계 상단의 실 경로를 보여주는 사진을 찍을 수 있다면 도움이 될 것입니다. 또한 타이밍이 맞지 않을 수도 있으며 일반적으로 후크가 바늘을 통과할 때 바늘의 스카프가 있는 위치를 보면 알 수 있습니다. 바늘의 눈은 바늘이 바늘을 통과하는 위치보다 1~2mm 아래에 있어야 합니다. 그렇지 않은 경우 후크를 조정해야 합니다. 사진의 후크가 많이 닳아 보입니다.

I haven't sewn it yet.
A little later....
Let's test by adjusting the height of the needle bar slightly, or by adjusting the height of the needle slightly.

[ddiuni]

There is no manual, and I have no idea why sewing is not working. This is a special glove sewing machine. Even if you look at the YouTube video, the video is blurry and you can't tell because it doesn't come out properly.