Search the Community
Showing results for tags 'springfield'.
Found 7 results
-
Hello, all. I believe this is my first post, although have observed for some time. I really appreciate all the wisdom shared through the forum. It's remarkable to find so many fantastic craftsmen who are also humble and encouraging to others who are working to hone their skills. I've made a few holsters over time. Have found that my different variations don't like sharp ejection ports. Especially noticeable on the recent project for a Springfield Hellcat (shown in attached pic). On this particular holster I find that almost any forward pressure on draw make the gun want to hang up as the forward edge of the ejection port digs into the leather, and especially the stitching. I did groove a stitching channel in hopes of mitigating, but this was not effective. In the past I have done holsters without a reinforcement panel, thus no stitching; this approach is an improvement, but still more scrape on draw that I like to see. On this latest project it is too severe to be acceptable, so I'm looking for methods to mitigate/eliminate the issue. What suggestions do you have? Am I missing something in my design or execution? Is this unavoidable with firearms with ejection ports with exterior edges that are not radiused? Thanks in advance for your wisdom.
-
Face and backside. Kimber Pro Raptor II with 4" barrel. High-ride with a 15-degree rake/cant.
-
Me and a friend both bought springfield armory xdm 9mm with suppressor heigth sights and added streamlight tlr1 weapon lights. Problem . No one makes a holster to accomodate yet. So i made this test pair. I will be making some adjustments to the pattern soon and making another pair but works pretty good so far. Also you can see stitching is not quite completed when i took these.
- 3 replies
-
- springfield
- xdm
- (and 10 more)
-
Me and a friend both bought springfield armory xdm 9mm with suppressor heigth sights and added streamlight tlr1 weapon lights. Problem . No one makes a holster to accomodate yet. So i made this test pair. I will be making some adjustments to the pattern soon and making another pair but works pretty good so far. Also you can see stitching is not quite completed when i took these.
-
- springfield armory
- pancake
- (and 10 more)
-
Just received my first order from Springfield Leather. I have heard mixed reviews about them so I ordered a small quantity of 6sf of Hermann Oak Leather (Shoulder, singles). (http://springfieldleather.com/30417/Shoulder%2CSingle%2CH-O%2C3-4oz/) Their customer service was friendly but the quality I received was unacceptable. Please see attached pictures for their imperfections . (I took the pictures in different rooms so the lighting is different) Maybe I was just unlucky. But that does not justify what I received. You have been warned... stasaki
- 28 replies
-
- springfield
- poor quality
-
(and 1 more)
Tagged with:
-
So I just received an email from one of their mail fulfillment people telling me that because there always seems to be an issue with my order, I should no longer order from them. - stop and let that marinate for a moment - they pretty much told a customer to get lost instead of striving for excellence in customer service as they claim to do. I have ordered from Springfield exactly 4 times. 3 of those orders have had errors - and ones that could have easily been avoided with proper internal processes in place. The first time what I ordered and what was sent were two different things. After some back and forth with customer support who actually spoke to me quite rudely and was combative, the owner, Kevin, stepped in and made it right, sending me what I required. I judge a business more on how it handles an issue than completely writing it off when there is one, so I ordered again based on this experience. The second order had two pieces of leather I ordered missing from the order, along with a big hole in one of the small pieces I ordered, making it pretty much unusable. Again, Kevin corrected this and sent me the correct pieces, and made an effort to source some leather I was having trouble finding. The third time had no issues - I received what I ordered. My last order was ordered 3 weeks ago and still hasn't arrived, and has ended up in California despite my mailing address being in Washington. When I contacted them about this they wrote back and literally asked me what I'd like them to do about it. I explained that as someone who runs a business when my customer tells me something hasn't arrived, even though it's usually the fault of the mailing system and not me, I go and figure out where it is and why it's stuck there before even responding, much less asking the customer what I should be doing. To this, I received the following response: "Obviously we’re not capable of doing business successfully with people that live in your part of Canada. In view of that, we’re requesting that you no longer order from us. We realize that you’re not at fault here, and I’m sure it will save much frustration on your part, and enable you to better supply your customers if you get your supplies from a more dependable vendor, like perhaps Tandy, or Oregon Leather. " This response shocked, baffled, and downright enraged me - and not only because they used my geographical location as a thinly veiled excuse to get rid of me 'politely'. Despite my shipping address being in Washington, where I'm located has no bearing on the majority of the problems I've experienced with them - they've been errors in processing an order and things that could be avoided with good internal processes in place. But telling a customer to get lost? And to go find a more "dependable" vendor? Why not strive to improve your dependability instead? I'm blown away by this way of 'solving' a problem - by essentially throwing a rug over it and pretending it doesn't exist rather than taking steps to ensure it doesn't happen again and again and again. If they screw up with me on 3 out of 4 orders, they are likely going to screw up with someone else pretty soon, if not already, so I hope in all sincerity that anyone considering shopping here thinks twice before placing an order, as you could very well be the next customer they decide to expel. I'm not sure how it is that they offer 'excellent customer service' to some, and treat others like garbage, and much less how they've survived doing so; but the idea of telling a customer to get lost because they cant get their ducks in a row is appalling and completely the opposite of excellent customer service.
- 57 replies
-
- springfield
- springfield leather co
- (and 4 more)
-
http://springfieldleather.com/29324/StarterSet%2CProfessionalProject/ Is it worth the money? As in the tools that are included?