Jump to content

Recommended Posts

  • Members
Posted

I figured I would give holster making a shot.

Here is my first attempt. It is 7/8 veg tanned shoulder from Zack White Leather, saddle stitched, Fiebings Mahogany dye, finished with Neatsfoot oil and Fiebings Bag Kote.

There are a few things that I can improve at and would do differently on my second attempt but for a first try I am very happy with the results.

It is for my Sig Sauer Mosquito .22.

Let me know what you feel needs improving and what you would have done differently.

picture018m.jpg

picture022z.jpg

picture020.jpg

  • Members
Posted

I think if my first one turns out that good I'll be pleased! I've got some leather on it's way and I'm ready to try my hand at it.

Stitching looks really nice. Did you mark your holes w/ an overstitch wheel, etc? What kind of thread did you use?

  • Members
Posted
I think if my first one turns out that good I'll be pleased! I've got some leather on it's way and I'm ready to try my hand at it.

Stitching looks really nice. Did you mark your holes w/ an overstitch wheel, etc? What kind of thread did you use?

Thanks for the kind words!

I marked the stitching with a 6:1" overstitch wheel then used a small drill in my drillpress to make the holes. I had one hole go bad when I let go of the powerhead on my drillpress and it dropped down drilling a hole in between marks. The thread I used was waxed brown nylon.

Good luck with your project! Hanging out here and reading is the best thing that you can do. I have learned so much here.

  • Members
Posted

I don't think I'm quite buyin' that you're a newb. ;) I cannot speak to how well it might function as a holster, but as far as the looks go, I would have guessed it was made by someone more experienced. Nice work!

Kate

Posted

Nice looking holster. My first couple of holsters were turned into dog toys. My only suggestion would be to run your stitch lines a little closer to the pistol in particular, the stitching around the bottom of the trigger guard. Keep up the good work, you will soon be dreaming up new holster designs when you sleep.

Randy

Randy Cooley

Bulldog Custom Gun Leather

www.bulldogleathercompany.com

  • Contributing Member
Posted

Ditto Randy's comment on stitch lines. Also, you'll probably want smaller belt slots. The large slots are great for pushing a belt through, but tend to be counter productive at keeping the holster where you want it. It just moves around too much with that much slack in the holes.

Very clean job with the saddle stitching, it looks great. Last thing: I know this is for a .22 plinker, but for more serious duty holsters really look into a sight channel. It keeps the front sight from peeling leather on the way out, or getting hung up in the holster. I once argued against them.....well, I use them now. One of my great moments of "open mouth, insert foot".

Mike DeLoach

Esse Quam Videri (Be rather than Seem)

"Don't learn the tricks of the trade.....Learn the trade."

"Teach what you know......Learn what you don't."

LEATHER ARTISAN'S DIGITAL GUILD on Facebook.

  • Members
Posted

I also say good first attempt....other than getting the stitching closer to the contour of the gun, I would suggest rounding off those sharp corners a little. They will take some knocks and get dog-eared after a bit.

Rayban
www.rgleather.net

  • Members
Posted

Thanks all for the kind words.

There are a couple things that I will be doing differently with my next holsetr...one being the stitching. I was so worried about stitching too close to the gun that I mis-judged and didn't stitch close enough. Also when I burnished the edge I used beeswax...That is what I had always done on my knife sheaths but I soon found that the staining doesn't take very well with the edges coated in wax (I have never dyed before but it is just common semse that dye wouldn't penetrate the wax...I don't know what I was thinking...)

As for the sight channel, I took that into consideration...I used a third layer of 7/8 leather between the frunt and back peice that essentially creates the sight channel.

Thanks for the critiques and keep them coming...that is how one learns :thumbsup:

  • Members
Posted

ydduit;

Nice job....

Boning - by hand or did you use a press. My first couple of holsters were not a pretty sight. In the trash they went.

NRA Member

Certified Firearms Instructor

www.agcustomgunleather.com

  • Members
Posted

You wrote: "Let me know what you feel needs improving and what you would have done differently."

First, . . . that's a pretty good job for the first one, . . . mine was no where as good.

But: already been said, . . . get the stitch lines closer to the weapon, especially the trigger side, and don't be too concerned about making it too small. I've had to do some shoving, tugging, and pushing on some that wanted to be too small, . . . but in the end, . . . leather does stretch, . . .

Secondly, . . . get rid of the points on the outside edges, . . . and add smooth curved flowing lines to it. The straight cut across the front has little appeal.

Thirdly, . . . also been said, . . . tighten up the belt slots a bit, . . . they may not be big, but in the picture they have that appearance. You want the belt to go in with just enough clearance that it goes in without shoving. The holster will then adjust to the belt as you wear it.

A big "Yessir" to the sight channel, . . . I mold mine with a 3/16 inch dowel taped to the top of the handgun so I get a good sight channel.

You might also take the time to learn to mold more of the weapon to the outside, . . . leaving the back (inside) flatter, . . . it makes it MUCH, MUCH more comfortable.

Finally, . . . face the flesh side into the inside (next to the human body) on the back piece on a pancake holster, . . . it makes a better looking rig, . . . and it doesn't move around any where as much.

Last point, . . . you did one of my favorite tricks that others do not do, . . . that is to mold in the safety to the back tang. I think it is very important as it will keep the safety on and not slide off, . . . which is very important for me in anything but a 1911.

May God bless,

Dwight

If you can breathe, . . . thank God.

If you can read, . . . thank a teacher.

If you are reading this in English, . . . thank a veteran.

www.dwightsgunleather.com

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...