Jump to content

Recommended Posts

  • Members
Posted (edited)

I'll start by saying I'm new to leatherworking, and I'd like to try to do this by hand if possible. (I don't have a machine.)

My main concern is sewing the foam channels/pleats to the leather to give it padded ridges. I've never seen anyone do this by hand. Is it possible?

I want to make the tan seat below. I've been eyeing a soft, 5-6oz latigo, but it might be too thick? I want a leather that will last and age nicely.

I'm up for ideas. Thanks.

 

racer-leather-seat-triumph-thruxton-1200-single-4.jpg

racer-leather-seat-triumph-thruxton-1200-single-3.jpg

pleats-foam.jpg

Edited by doorty
added link for video
  • Replies 27
  • Created
  • Last Reply

Top Posters In This Topic

Posted
22 hours ago, doorty said:

sewing the foam channels/pleats to the leather to give it padded ridges

I do believe this is done by using a medium weight padding, which is squashed down along the stitch lines, on the tan seat anyway. On the grey piece in the last pic, it appears the foam padding, which is thicker than on the tan seat, is cut into strips and gives more depth to the stitch lines.

As for the best leather to use for your project, I will have to leave that question for somebody who actually knows what they are talking about, 'cos I don't.  

Kindest regards

Brian

 

"Whether you think you can or whether you think you can't, you are right"  Henry Ford

Machines: Singer 201p, Kennedy,  Singer 31K20, Singer 66K16 ("boat anchor" condition), Protex TY8B Cylinder Arm (Consew 227r copy), Unbranded Walking Foot (Sailrite LSV-1 copy)

  • Members
Posted (edited)
19 hours ago, Rockoboy said:

I do believe this is done by using a medium weight padding, which is squashed down along the stitch lines, on the tan seat anyway. On the grey piece in the last pic, it appears the foam padding, which is thicker than on the tan seat, is cut into strips and gives more depth to the stitch lines.

Right, but can you do it without a machine?

You gave me an idea, which is to do the leather stitching first and then glue strips of foam between the stitching. it's a bit of a hack, but it might work if the glue is strong enough.

Edited by doorty
Posted
1 hour ago, doorty said:

do the leather stitching first and then glue strips of foam between the stitching

I would think you could stitch with a machine or by hand to achieve this effect by stitching right through the foam padding..

I don't understand how you would stitch first then glue the foam between the stitching. That seems to me, like making a sandwich then inserting the ham after its all together.

Kindest regards

Brian

 

"Whether you think you can or whether you think you can't, you are right"  Henry Ford

Machines: Singer 201p, Kennedy,  Singer 31K20, Singer 66K16 ("boat anchor" condition), Protex TY8B Cylinder Arm (Consew 227r copy), Unbranded Walking Foot (Sailrite LSV-1 copy)

  • Members
Posted (edited)
3 hours ago, Rockoboy said:

I would think you could stitch with a machine or by hand to achieve this effect by stitching right through the foam padding..

I don't understand how you would stitch first then glue the foam between the stitching. That seems to me, like making a sandwich then inserting the ham after its all together.

How would you manually sew on the foam side? You wouldn't be able to see the holes though the foam.

Edited by doorty
  • Members
Posted

Just spit balling here.

What about using two pieces of leather and strips of foam or are these already using two pieces of leather? Either way, it looks like you could stitch the leather to the leather at the outer edge then glue your first foam strip then glue and stitch the two leather layers then repeat. Alternatively, you culd glue the strips of foam to one of the two leather layers then glue the other leather layer to them. Then move on to stitching.

Posted
3 hours ago, doorty said:

How would you manually sew on the foam side?

I am leaning towards what @Bolt Vanderhuge said above, (if I understand what he wrote), where you use 2 pieces of leather with foam sandwiched between and stitched right through the whole lot. Alternatively, use 2 pieces of leather with small pieces of foam, cut to fit each individual segment, and stitched around the outside of each piece of foam and through both pieces of leather.

Kindest regards

Brian

 

"Whether you think you can or whether you think you can't, you are right"  Henry Ford

Machines: Singer 201p, Kennedy,  Singer 31K20, Singer 66K16 ("boat anchor" condition), Protex TY8B Cylinder Arm (Consew 227r copy), Unbranded Walking Foot (Sailrite LSV-1 copy)

  • Members
Posted (edited)
2 hours ago, Rockoboy said:

I am leaning towards what @Bolt Vanderhuge said above, (if I understand what he wrote), where you use 2 pieces of leather with foam sandwiched between and stitched right through the whole lot. Alternatively, use 2 pieces of leather with small pieces of foam, cut to fit each individual segment, and stitched around the outside of each piece of foam and through both pieces of leather.

I was saying use strips of foam . Stitching only thru leather that is glued together. That way the needle has only one hole to go thru instead of having to feel for the hole in the second piece of leather that is on the other side of foam. So basically your alternate suggestion was what I was trying to say.

Edited by Bolt Vanderhuge
  • Members
Posted
10 hours ago, Bolt Vanderhuge said:

I was saying use strips of foam . Stitching only thru leather that is glued together. That way the needle has only one hole to go thru instead of having to feel for the hole in the second piece of leather that is on the other side of foam. So basically your alternate suggestion was what I was trying to say.

Thanks guys. It sounds like it'll work. The internal leather will never be seen, but I could shop for some cheap leather to use for that.

Any thoughts on 4-5oz Latigo for the outside cover? 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Create New...