Jump to content

Recommended Posts

  • Members
Posted

Recently purchased a 153k103 cylinder arm walking foot machine. The machine worked fine days before I picked it up and brought it over to my place. The walking foot is stuck in the up position and lever behind it isn’t working, no tension. The pedal is connected as should be but I don’t feel any tension whenever the pedal is pressed, I have a feeling something is stuck. Not much of a mechanic and the manuals don’t explain much on these matters. Any help would be greatly appreciated!

IMG_0369.jpeg

  • Replies 45
  • Created
  • Last Reply

Top Posters In This Topic

Posted

Put some oil in the bushings there's an upper & lower one where the bar runs through.Then push or tap on the foot & it should go down.Don't loosen the circled screw.

Bob Kovar
Toledo Industrial Sewing Machine Sales Ltd.
3631 Marine Rd
Toledo,Ohio 43609
1-866-362-7397

toledo-banner-2.jpg

  • Members
Posted
17 minutes ago, CowboyBob said:

Put some oil in the bushings there's an upper & lower one where the bar runs through.Then push or tap on the foot & it should go down.Don't loosen the circled screw.

No luck, the walking foot isn’t budging at all, whenever I firmly press the pedal those 2 components move slightly IMG_0372.thumb.jpeg.c621f931f6c76527423d1c1d2e6dc8ba.jpeg

  • Members
Posted
10 minutes ago, Lgbrs9 said:

No luck, the walking foot isn’t budging at all, whenever I firmly press the pedal those 2 components move slightly IMG_0372.thumb.jpeg.c621f931f6c76527423d1c1d2e6dc8ba.jpeg

If you lift the lever for the walking foot behind the machine the components also slightly move

Posted (edited)

Put some oil on the bar just ahead of the lower circled part,you could try tapping on the rightside of the L-piece just above the small bar.One more thing to look at is on the first pic,you have a lifter bar that picks the foot up,take it off & the then take the big headed screw out & look at the bottom,there's a release pin there that could of slipped backwards holding it up.

Edited by CowboyBob

Bob Kovar
Toledo Industrial Sewing Machine Sales Ltd.
3631 Marine Rd
Toledo,Ohio 43609
1-866-362-7397

toledo-banner-2.jpg

  • Members
Posted
9 minutes ago, CowboyBob said:

Put some oil on the bar just ahead of the lower circled part,you could try tapping on the rightside of the L-piece just above the small bar.One more thing to look at is on the first pic,you have a lifter bar that picks the foot up,take it off & the then take the big headed screw out & look at the bottom,there's a release pin there that could of slipped backwards holding it up.

Can this be said pin? 

IMG_0374.jpeg

Posted (edited)

Yes,push it in.

IMG_0374.jpeg

Edited by CowboyBob

Bob Kovar
Toledo Industrial Sewing Machine Sales Ltd.
3631 Marine Rd
Toledo,Ohio 43609
1-866-362-7397

toledo-banner-2.jpg

  • 3 weeks later...
  • Members
Posted
On 1/9/2024 at 6:26 AM, CowboyBob said:

Yes,push it in.

IMG_0374.jpeg


everything worked fine, last night ran into some issues again. Machine was stitching fine then suddenly the walking foot wouldn’t lift. The presser foot would move fine but the walking foot was stuck,no walking whatsoever, as I tried fiddling with it I got the presser foot to go up and now it is stuck in the up position. The release lever and button won’t drop it and I can’t seem to find the area that’s causing this to happen. 

  • Members
Posted
2 hours ago, Lgbrs9 said:


everything worked fine, last night ran into some issues again. Machine was stitching fine then suddenly the walking foot wouldn’t lift. The presser foot would move fine but the walking foot was stuck,no walking whatsoever, as I tried fiddling with it I got the presser foot to go up and now it is stuck in the up position. The release lever and button won’t drop it and I can’t seem to find the area that’s causing this to happen. 

What I also noticed is that the bobbin isnt moving while I turn the wheel

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Create New...