Workbench Height

[amuckart]

There are some good books on making woodworking workbenches that go into the ergonomics of bench height in quite a lot of detail. The activities aren't all that dissimilar in terms of where you want your work located relative to your body. Scott Landis' The Workbench Book is one of the best ones. The Workbench Design Book: The Art and Philosophy of Building Better Benches by Christopher Schwartz is another good one.

Lee Valley Tools has all the three best workbench books for sale.

[cem]

Mine sit about 36", I have a wrap around the room arrangement using kitchen cabinets, I'm short though 5"3' so need to use a drafting chair when sitting down.

Clair

[dirtclod]

Mine is 38 inches tall and i'm 4 foot 22 inches tall.

[Dallas Cowboy]

I built my bench today. After careful consideration and reading what most people like, I chose to make mine at 42" tall and 3'x6'. I love it!! It seems to be the perfect height for me. I can sit on my adjustable stool or stand and don't have to hunch over and hurt my back or my shoulders. This thing is solid and strong as a Rock. I usually over build stuff and you could probably put an engine block on it. The legs are 4x4's and the framing is 2x4's and the top is 3/4" mdf board I'll try to get some pictures to post.

Edited May 27, 2012 by Dallas Cowboy

[FHL FERG]

I am in the process of building a new bench right now. I decided to go 48" so I can use it standing or sitting on an adjustable drafting chair. I'm 6'1" and this puts my elbows at a nuetral 90degrees sitting or standing.Good luck and go a little taller with it, if ti's too tall you can always trim a little off the legs.....

[FHL FERG]

And then I read your last post, so it sounds like you made the right choice. Hunching over is what has been killing me too. I'm building mine out of cedar and hand scraping it to smooth and level the top as well as give it some character. fingers crossed that I didn't waste all that money on cedar......

[mikesmith648]

I am working the next 3 nights in the ER and then will be off for 5 days. Planning on going to work on my trailer and building the work bench in it so I can do my leather and not have to carry everything in the apartment wherever I go. Also will help keep everything more organized that way...I hope. Once I get it all finished I will post pictures. Planning on using a rolling desk chair with adjustable height and making the bench about 42" tall after reading the posts and suggestions. Also, I am going to wire the trailer for lights and a fan and heater so I can work in comfort. Just plug it in and go! This setup will also keep the neighbors from complaining about all the tapping as I work.

Mike

[Chief31794]

My Carving Bench, Dying Bench and Sewing Bench are all 36" high, the Carving area comes out about 39" after I place a rubber Poundo Mat then a Granite Slab on it. I stand some and set some on a work stool. I'm not as tall as some of the folks (around 5' 9") so it works pretty well for me.

Ken

[BondoBobCustomSaddles]

Well, I am 5'9" and currently my work/tooling bench is set at 34". Guess that this post has made me re-think the height, so next time I am working in the shop I think I will raise the bench 4" or so and see it there is any difference. currently I use the back end of my stitching horse as my stool, been doing that for 20 or so years now. Guess I'll re-think that also. We'll see.

Bob

[Neillo]

Hey guys, thought i'd pitch in on the subject after much research into building a bench for woodworking.

the way I planned mine was to make the height of the benchtop about 100mm/4" lower than my elbow joints

while standing.

This way, i have great control over my tools due to being slightly lower than my elbows. I'm working on a stool

that allows my hands to be at the same level when sitting so i can do more delicate work.

Oh, and a top thickness of 1 3/4" - 2" helps a lot! i do all my stamping over the leg joint of the bench corner,

works a treat.