Members Haleyf Posted February 8, 2013 Members Report Posted February 8, 2013 I want to know the order of operation in leather strap work. I am trying to start a business selling custom dog collars. I want them to be quality and I seem to run into some kind of problem with every step I take. Here is the method I have adapted to so far: (I will note some of the other problems to see if I can get some extra advice.) 1. Cut and skive the leather with super skiver- (can't really find the trick to making this an easy task) 2. Sand the edges and the raw side of leather (for comfort) with a sanding wheel on a drill press 3. Bevel the edges 4.. Punch holes, wet and stamp 5.. Dye with the color of choice - Fiebings oil based Cordovan dye, Fiebings acrylic antique medium brown stain or a zelikovits water based pigment pink dye (pink seems to have streaks where the color doesn't take no matter how many coats I add and rubs off easily) 6. Let dry for an hour or so then color the letters with sharpie for the stained collars, metallic markers or paint markers for the dyed collars(paint markers are difficult to make even and not globby and metalic markers seem to wear off a little) 7. Spray with leather sheen 8. Let dry for an hour or so then burnish the edges with glycerin and saddle soap or Quik Slick on a nylon slicker attached to the drill press. (I am not sure how long this is supposed to take but it seems like forever and I still never get glass smooth edges) - ordered a wooden burnisher made for a drill press so hopefully it will help. My other problem is that sometimes the edges seem to crack in certain spots mostly around the buckle within just a few days. I use quality herman oak leather. 9. touch up the edges with the same dye 10. condition with lexol conditioner. 11. add hardware Ok... so where I get mixed reviews is at what time to apply the finishes and the conditioner. I am so confused that I kind of change it up every time I make one so I don't know if the order of operation is contributing to any of my problems or not. OR if the order of operations needs to change depending on what base of dye and marker I am using. I have been told to condition right after you stamp and before you dye and let it sit over night. I have been told you always put any oils conditioners or saddle soap very last because other products wont penetrate. I have also been told it's super important to use the leather sheen finish before you finish the edges and within two hours of dying But if a water resistant finish is applied won't it seal the leather from absorbing any other products - like conditioners, edge burnishing products and touch up dye?? I feel like if I understood the chemistry behind all of these products I would have a rule of thumb So confused. Any advice would be excellent! Quote MultiQuote Edit Quote
Members Cyberthrasher Posted February 8, 2013 Members Report Posted February 8, 2013 First thing on my list is "I have been told you always put any oils conditioners or saddle soap very last because other products wont penetrate." You may be confused about the nature of oils/conditioners. These products penetrate the leather themselves and do not offer any real protection. But, any of your waxy conditioners can stop proper coverage of any additional products. The oils on the other hand, when left to sit, shouldn't be an issue. What are you using for a conditioner? You can't beat good old pure neatsfoot oil for this step. It's a tried and true product that should serve you well. How smooth are you sanding your edges prior to burnishing? Before edge slicking, your edge should be pretty dang smooth and already formed to the proper shape. i usually hit mine with a 150 grit to start forming the round edge I like (after using an edge beveler) and then follow it up with 400 grit wet/dry. From there, a little glycerin soap and my dremel burnisher, dye the edge (don't worry about it penetrating like the rest of your product), rub it down with beeswax and a piece of denim/canvas to a nice glassy shine. Remember, the edge burnishing products are only meant to really lubricate things and make the fibers lay down, not be absorbed by the leather. usually, I actually apply my finish to the complete project and my edges as the very last step. I was looking at Fiebings Leather Sheen for another member who was considering it and, after reading the description on the can, I pretty much came to the conclusion that this is not a permanent finish. It's more of a temporary finish/conditioner to be used on the end product as part of a continuous maintenance routine. The key part that led me to that was "Shines and conditions leather with a flexible wax finish". To me that sounds more like the kind of thing you'd tell your customer to use after you've already applied a more permanent finish over your dye (like saddle-lac, resolene, clear-lac, etc...) I'm actually at the day job now, so I'm going to defer to others to fill in the gaps that I've left out. Quote hellhoundkustoms.wordpress.com www.facebook.com/hellhoundkustoms www.etsy.com/shop/HellhoundKustoms
Members Haleyf Posted February 8, 2013 Author Members Report Posted February 8, 2013 cybertrasher - You bring me to a ton of other questions I have. SUPER NEWBIE ALERT! Iv'e been using lexol conditioner. I guess because I read somewhere that some type of conditioner is important. It does seem to make the leather more pliable to hammer in the hardware. Does neatsfoot oil count as a conditioner? I use the saddle soap to finish the edges which I was also told to apply after the finish... "your edge should be pretty dang smooth and already formed to the proper shape.I sand my edges until they are soft. Only takes about a minute to a minute and a half but they remain the same shape. Are you saying that I should bevel the edges first and then it will make them round? And I guess the term smooth confuses me because when you sand leather it makes it soft and fluffy. When I think smooth I think slick.. I also don't know what a 50 grit 400 grit wet/dry means. I will go ahead and live up the stereotype that I am a girl and don't know S*&% about tools. I just have this sanding wheel my dad bought me on his drill press that goes up and down in speeds marked with a plus or minus sign. lol Do you dye the edges at all with the rest of your product before burnishing or just leave them bare and do it after burnishing? Then.. how do I apply the beeswax? I did that once over a whole collar by just rubbing it on and then trying to buff it off, but it left residue. do you melt it? Also I use leather sheen because of it's water resistant qualities for a product that is made to last outdoors. I watched this youtube video about finishes to come to this conclusion. https://www.youtube.com/watch?v=zyTg_hfpNUM&noredirect=1 What would you consider a permanent finish? And should I use it with the conditioner and the leather sheen or is that unnecessary? See SUPER NEWBIE ALERT!! Quote
Members Haleyf Posted February 8, 2013 Author Members Report Posted February 8, 2013 Also.. Forgot to mention that in order to make this worth my time I need to finish a 20 inch strap in about an hour but make it as good a quality as possible.. How long does it take you all to do a strap edge? Quote
Members jk215 Posted February 8, 2013 Members Report Posted February 8, 2013 - Neatsfoot oil is a very widely used conditioner. It will make the leather more supple and mallable. - You will want to bevel your edge and then sand. It will start to take on a rounded appearance. Once it is decently smooth you will dampen the edge with a water/saddle soap combination. Make sure its not sopping wet, just enough to aid in the burnishing process. Nothing goes on after you finish the edge. So your process would be : 1. Bevel and sand 2. Burnish with water/saddle soap combo. 3. Dye the edge 4. Final burnish 5. Apply finish to the edge Quote http://shop.makesupply-leather.com - Custom and Stocked Acrylic Templates
Moderator immiketoo Posted February 8, 2013 Moderator Report Posted February 8, 2013 Haley, it sounds like you need to spend some time working the leather to learn what works for you. There are NO hard fast rules in leather, minus a few obvious ones. You should check our Bobby Park's (Hidepounder) tutorial on edge finishing. Here's the rub (Pun intended) To create the edge you desire in the time frame you desire, you will need to either eliminate steps in your process, automate steps in your process or make it so efficient that you stay profitable. I don't know where you came up with 20 minutes, but the only way to gain speed and efficiency is to practice. A lot. A tip to cut time considerably in the process is to buy pre-dyed leather, possibly bridle or latigo leather. Both of these have oils and waxes in them that make them weather resistant. Of course, they are more expensive, but as a business, you need to calculate your time into the equation. Two hours of waiting for dye to dry is time that could be spent elsewhere in the process. Good luck, and welcome to LW.net Mike Oh yeah. Skiving sucks. Again, its a time-in-grade thing. Also, the better quality leather you use, the better off you will be when it comes to skiving. Quote Learnleather.com
Members Cyberthrasher Posted February 8, 2013 Members Report Posted February 8, 2013 (edited) Ah, thanks to the others for filling in some of it. With their comments, I'm going to jump straight to the grits. The number on the sand paper relates to how course it is. The lower the number, the more material it removes. A 150 grit sandpaper will remove enough material to shape the edge of your leather (after edge beveling) and start the smoothing process. The 400 grit wet/dry paper (it can be used wet without falling apart) will really smooth things out without removing a whole loot of material. You can probably get both of these at your local hardware store, but you may have to go to an auto store for the 400 grit wet/dry. You have to bevel the edge though in order to start getting that round shape. It knocks off the corners of the edge and leaves a flat spot in the middle. This is where the sand paper comes in to start shaping things. I should add that I just use a piece of the sandpaper curled up in my fingers to match the curve of the edge when I'm doing this. It's what works for me. With practice, there's not reason you can't get all of these steps in an hour. I do all my edge work on 50" guitar straps in about an hour to an hour and a half, including dyeing. But, if that hour includes the entire time to make the collar you're going to have to find ways of streamlining stuff. For the beeswax, I have a block of it that I rub down the edge so it makes a groove in the block and then rub the edge briskly with my denim/canvas to basically burnish the wax into the low spots and crevices of the leather. If you have a buildup of wax, you'll probably have to use 2 cloths. One to remove the excess and another to do the final rubbing. Hidepounder goes over a lot of this in his tutorial in the "how do I do that" section of the forum, and then from there it's just a lot of experimentation to figure out what works best for you. I'm always adjusting my procedure or trying new things as I hear about them. Edited February 8, 2013 by Cyberthrasher Quote hellhoundkustoms.wordpress.com www.facebook.com/hellhoundkustoms www.etsy.com/shop/HellhoundKustoms
Members Haleyf Posted February 8, 2013 Author Members Report Posted February 8, 2013 Mike - Thank you! I have looked at bob parks method and that's why I use the quik slik or the saddle soap. It does work way better than the other things I have tried. Can't quite figure out how to attach the canvas to a mechanical burnisher though. Also I said 20 inch piece of leather in around an hour(without counting dry times). Not 20 minutes. I have quite a bit of experience working with my mom on leather straps. We never finished the edges or used anything but antique stains though and just sprayed at the end with a acrylic wood finish. Here is what she does www.saintbernardkeg.com This is a project I am launching to make some money to stay at home with my new baby and it is quite a different process to make a product that will remain comfortable, fasionable and durable around a dog's neck all the time here is a rough draft of a website I made for what I do (www.cowtowncollars.com - HONEST opinions for my first collars are welcome! Good advise about the latigo leather! I am going to look into it. Thanks! Cyberthrasher - Great info! I feel much better about sand paper now! That explains a lot. I will check out the forum post. BTW I saw your facebook and I really like your work! Before my little one came I used to do band and venue management and got my degree in music management. I will try to through some hooks out for you! Quote
Members Cyberthrasher Posted February 8, 2013 Members Report Posted February 8, 2013 (edited) Cyberthrasher - Great info! I feel much better about sand paper now! That explains a lot. I will check out the forum post. BTW I saw your facebook and I really like your work! Before my little one came I used to do band and venue management and got my degree in music management. I will try to through some hooks out for you! I saw that you're my newest like!! Bob attaches his canvas to a motorized system, but I'd say until you get a larger setup and more experience, the dremel burnisher would be a much better alternative for you. I use my canvas by hand rubbing briskly. If I ever get enough space and resources, I'd probably definitely have a motorized unit the size of his as well . Right now I'm working out of a corner of my basement, so space is tight. Oh yeah, take a look at the prototype amp handle I have on there, as well as the latest tooled black belt, and look at the edges on them. Those were both done with the procedure I laid out above. The amp handle isn't a finished product, but it will give you an good idea of the edges smoothness and shape. The belt is finished though with dye and Resolene (front back and all around since the customer wears a lot of khakis for work). Edited February 8, 2013 by Cyberthrasher Quote hellhoundkustoms.wordpress.com www.facebook.com/hellhoundkustoms www.etsy.com/shop/HellhoundKustoms
Members Cyberthrasher Posted February 8, 2013 Members Report Posted February 8, 2013 Oops! Just realized that amp handle prototype isn't on there. I posted it to my blues group as a teaser picture It's all scrap bin stuff, so nothing to be too proud of in this state, but you can kind of see the shape and smoothness of the edges. I have some closeup pictures somewhere at home. Quote hellhoundkustoms.wordpress.com www.facebook.com/hellhoundkustoms www.etsy.com/shop/HellhoundKustoms
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.