Members RoosterShooter Posted April 23, 2015 Members Report Posted April 23, 2015 I was thinking about purchasing a couple electric burnishers the other night and ran across a video on Youtube where a guy was using his homemade model. He didn't tell how he made it, but just had pics. I have several old bench grinders that have 1/2" arbors on them, and I have several burnishers that I purchased from someone along the way. Pictured below is my burnisher, and , as stated above, my bench grinders have 1/2" arbors. What else do I need? Quote
Members JAZZMAN Posted April 23, 2015 Members Report Posted April 23, 2015 Hi rooster, and i know this is not quite what you asked for, but have you thought abut getting one of these, Nigel says it fits on a half inch shaft and it looks pretty good, i have heard good things about these. Quote
Members RoosterShooter Posted April 23, 2015 Author Members Report Posted April 23, 2015 Hi rooster, and i know this is not quite what you asked for, but have you thought abut getting one of these, Nigel says it fits on a half inch shaft and it looks pretty good, i have heard good things about these. You didn't send a picture with your post so I don't know what you are referring to. Thanks Quote
Contributing Member JLSleather Posted April 23, 2015 Contributing Member Report Posted April 23, 2015 (edited) If you already have a motor you want to use, and already have that burnisher, then all you need is a sleeve that fits the 1/2" shaft and the shaft of that toy. Maybe go an inch down each one. Maybe git all smanky fancy and put a set screw through each end. Any machine shop kin make one in half an hour. Or, if a feller had a drill press, proper size reamers, and a small tap (maybe 1/4-20 or 5/16-18) you could make it yourself in that same half hour. Personally, I must be gittin lazy, cuz if I had a drill press I'd probably just stick the burnisher in it and use it like that But, you did say you wanted to use the bench thing .... Say, for instance, yer burnisher had a 3/8" shaft. Then a feller could take a piece of pipe with a hole LESS than 3/8". Drill one end out to just under 1/2", and then ream both ends (.376 and .501). Put a setscrew in each end as shown. Slip the 1/2" end on the motor and snug. If you wanna swap toys, you can slip it off the motor and leave it on the burnisher (wooden end). No slipping. No coming loose. Total investment, $30 at a shop / $2.38 if you do it yerself Edited April 23, 2015 by JLSleather Quote "Observation is 9/10 of the law." IF what you do is something that ANYBODY can do, then don't be surprised when ANYBODY does.
Members camano ridge Posted April 23, 2015 Members Report Posted April 23, 2015 (edited) Rooster, go to Lowes get a key-less drill press chuck. It will fit on your arbor and you can easily change burnishers or what ever you want to put in the chuck. You can eve get one for each side. Here is a picture of that type of set up Red Cent posted the other day on another thread. Edited April 23, 2015 by camano ridge Quote https://www.facebook.com/CamanoRidgeCustomLeather?fref=ts
Members JAZZMAN Posted April 24, 2015 Members Report Posted April 24, 2015 You didn't send a picture with your post so I don't know what you are referring to. Thanks Sorry about that Rooster, this is what i meant to post. Quote
Members veedub3 Posted April 24, 2015 Members Report Posted April 24, 2015 My setup is like the one in the photo Camano posted. Lowes doesn't carry the drill chuck in my area, but I did find it at Home Depot. Check here: http://www.homedepot.com/p/Ryobi-1-2-in-20-Drill-Chuck-and-Key-A10KC03/203000648 You have a bench grinder, and you already have a burnisher, screw the chuck on (It fits 1/2 arbor), insert the burnisher in the chuck and you are off! Karina Quote "The only man who makes no mistake, is the man who does nothing." Theodore Roosevelt
Members RoosterShooter Posted April 24, 2015 Author Members Report Posted April 24, 2015 Do I need to slow the motor down at all, or are the higher RPMs ok? Quote
Members camano ridge Posted April 24, 2015 Members Report Posted April 24, 2015 Mine runs at 3500 rpm and does just fine. I have a friend who has one that turns at 1750 and it does a good job as well. Quote https://www.facebook.com/CamanoRidgeCustomLeather?fref=ts
Contributing Member JLSleather Posted April 24, 2015 Contributing Member Report Posted April 24, 2015 Do I need to slow the motor down at all, or are the higher RPMs ok? Keep in mind that if you run one speed all the time, the larger end will create more friction and heat than the smaller speed - though the "speed" is the same. No long speech -- try it, you'll see what I mean. Quote "Observation is 9/10 of the law." IF what you do is something that ANYBODY can do, then don't be surprised when ANYBODY does.
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.