Members Kryptonite Posted November 9, 2017 Author Members Report Posted November 9, 2017 A shout out to Bob at Toledo Ind. Sewing for making this great reducer pulley. I can slow a stitch to an absolute crawl. Will Quote
Members Cbm Posted November 10, 2017 Members Report Posted November 10, 2017 Thanks will this fixed it it works now Quote
Members Turnaround Posted December 21, 2017 Members Report Posted December 21, 2017 Per Kryptonite's mention of the "add on" transmission to slow the speed of our walking foot machines. My add on transmission and extra belt, seems to have changed the mechanical advantage of the motor so much, that, when I try to rotate the handwheel, to line up the needle during a partial stitch, the original Juki LU-563"s handwheel is pretty much impossible to turn, . My "work around," when I need to hand turn and move the needle position a little, is to pick up the sewing machine "head" an inch or two, and then stick a large, plastic, screw driver handle between the head and the table. Jacking up the head releases the belt tension a little, which allows me to hand turn the machine like I could before I added the accessory transmission (please understand, I dearly love this transmission and smaller clutch motor pulley) for slowing the feed about six to one slower. Although it might be a little too slow if and when I get better at sewing. Maybe changing to a "servo motor" instead of fooling with an "add on transmission" and "clutch motor" would have been a better choice? I do remember reading somewhere, a recommendation about not using an automobile fan belt, because the sewing machine operator needs the drive belt to slip a little, so maybe my belt is just gripping the pulleys too well. I am new at this, and have never seen a sewing machine belt, so how are they different? Round instead of Vee?. Any body got a better idea, like maybe adapting a six pound, big hugger large diameter handwheel off a Sailrite sewing machine? Quote
Members dikman Posted December 21, 2017 Members Report Posted December 21, 2017 If you operate the foot pedal just a little (not enough to engage the clutch) it should release the brake in the clutch motor, allowing the pulley to turn. Quote Machines wot I have - Singer 51W59; Singer 331K4; Seiko STH-8BLD; Pfaff 335; CB4500. Chinese shoe patcher; Singer 201K (old hand crank)
Members Kryptonite Posted January 1, 2018 Author Members Report Posted January 1, 2018 I can turn my handwheel enough to move the needle/stitches without to much trouble, but it is stiff. A little less belt tension might help you get some pressure off the handwheel so it will move for you. I would at least try that. For multiple hand stitches I have been lifting the head and removing the v-belt. Auto V-belts work ok. I just happen to have a Sailrite 6 pound handwheel. Mounting problems aside, I don't see it as an fix. You are still going to have the high belt tension and now even more weight to start rotating, more force required. Cheers, Will in Central Florida Quote
Members TXJax Posted May 3, 2023 Members Report Posted May 3, 2023 On 9/3/2017 at 4:02 PM, Uwe said: I mentioned that feed rod alignment in my video as a workaround for machines where the opposing arrow plate is missing. If you have both arrows, use just them. I just checked five of my machines and on every single one of them the feed dog is in its front-most position when the take-up lever is at its highest point. I doubt that the correlation is a coincidence and have a strong feeling that the correlation is one of those general, if unwritten, rules that apply to many sewing machines. It's a quick sanity check, if nothing else. Your machine may well have multiple issues that need to be corrected. Following Eric's advice is your best bet. OMG, Uwe, I love you!!!! I bought a 111w155 off ebay. It had a broken feed rocker shaft. I bought the new shaft but could not figure out the correct position of the feed dog! Your video showed me that the stitch regulator was off a little, and that the feed dog was off. Now my machine walks properly!! THANK YOU SO VERY MUCH! If you have a machine that seems to feed backward, check that your safety clutch "S" screw is in the groove, and that the stitch regulator "S" screw is in the groove. Quote
Members Wyowally Posted May 3, 2023 Members Report Posted May 3, 2023 I actually bought a new replacement eccentric just so I could understand how they're designed to work. Never had to install it though. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.