Can You Help Identify These Tools?

[MedusaOblongata]

I bought a lot of old, used leatherworking tools. Most I identified, cleaned up, and put to work. These few left me with some questions.

#1 has this pattern, not sure what it would do.

#2 might be a creaser(?) but it would leave a line pretty far from the edge if so.

#3 has three curved sides heading towards the point. The edges aren't sharp, but they seem sharpenable, though I wouldn't see why.

#4 has a point like a scratch awl, but the barrel is textured like a file, and the wire wrapping on the handle seems a bit like overkill since awls are simpleish. Maybe just homemade?

#5 Is has a 1/8" hole from the end of the handle all the way through, though I don't know why

#6 is flat on the back/top end, though it's textured around the sides of the top. The lower half is rough enough that side is uncomfortable to hold. I have rasp dremel bits similar in structure.

#7 is well worn, but could has a curved and sharpened end

#8 is round on both ends, knurled in the middle. It could be a pin punch for very large pins.

#9 could be a very wide edge beveler, though it's so dull it would take an hour on a grinder to get any kind of edge on it.

 

Thank you for taking the time to look over these for me.

 

 

[fredk]

quick look

#1 is a counter sink maker, for woodworking, turn it to cut a countersink hole for screw head

#9 is an upholstery tack lifter, push the v under the tack head to lever the tack off

#6 looks like a tapered hole-reamer, for enlarging holes slightly

#4 looks like a parallel hole reamer, for cleaning holes already made

#8 looks like a nail setter - for the final whacking of a broad-head nail to set it flush with woodwork

[zuludog]

I suspect these are some woodworking tools that have been mixed in, though they might be used when wood & leather are combined, perhaps a saddle or furniture, and I go along with FREDK

#1 is a countersink bit, used to set a flat headed screw below the surface of wood. It fits into a carpenter's brace, as in brace & bit

#2 is a tack lifter, for use on furniture and carpets

#5 could be a turnscrew, used to fit grub screws and bushes that have just a couple of holes instead of a slot 

#8 is a wide diameter nail punch, used to set the head of a nail flush or just below the surface of wood

Edited December 28, 2020 by zuludog

[ryano]

#2 is an edge wheel for shoe making or repair.

#3 is a metal deburring knife used in machining, etc.

#5 looks like a spanner screw driver.

#6 has me baffled as I have never seen holes drilled in the flutes like this tool????

[Aven]

#2  is a glazing iron.  Used on the welt of shoes.  They come in different widths.  It doesn't leave a groove, it gets heated up and smooths the welt.  The lip rides the edge of the sole so that you don't burn the upper.  There are ones without a lip that are used on the heel.

 

[ryano]

22 hours ago, Aven said:

#2  is a glazing iron.  Used on the welt of shoes.  They come in different widths.  It doesn't leave a groove, it gets heated up and smooths the welt.  The lip rides the edge of the sole so that you don't burn the upper.  There are ones without a lip that are used on the heel.

 

Aven,

I knew that it was used to go around the edge of soles, so the wheel just aides the tool by creating less friction as it goes around the edge of the sole? Why do some of these tools have different coarse straight knurl lines on the wheels? Also why does the part of the tool that smooths out the welt have a small edge landing, almost like the edge guide has an edge guide?

I have seen these tools with different wheels patterns (more like knurlings) on them and also have seen them heated and used as decorative markings on the soles of shoes inbetween the stitching and edge of the sole, which is not be the proper use of the tool. 

Thanks, 

 

[fredk]

I'm not sure

#2 is for a shoe sole, I think its a book binders edger

[Aven]

Ryan, it is entirely possible I am wrong.  I didn't see a wheel, but I'm viewing the forum on my phone.

[Sheilajeanne]

I'm guessing #9 is a tack/nail puller.

Oops, Fred said that already!

Edited December 29, 2020 by Sheilajeanne

[MedusaOblongata]

Thank you so much. You guys are smart and helpful. I appreciate it.