All Activity

First question. Is safety clutch disengaged? If not, it is out of time and you must time each hook separately. glenn

The end cam is worn. Replace it to take out the play. glenn

Hi, I am interested if it's still available.

I use glazed pigskin. Thin & stiff

Slow setting contact glue

a. the drill chuck being rotatable is good as you can fine tune the alignment b. I have one of Tony's patterns and there is a quadzillion holes to punch. The press & 6 hole punch really speeds it up c. The press I have doesn't have a large reach so I can't do holes towards the centre of the pattern with the press (oh dear, how sad, never mind!) I take my pattern out side to do those holes d. you have a good height on that drill press. The leather press I have hasn't great height and I had to replace the bar on my multi-hole punch with a much shorter one and cut down the single types

I haven't searched that way before. Thanks for the tip. I'll give it a try. I just put my 5mm hole punch into the drill press and didn't turn it on. It was easy for me to go through this heavy leather just pulling down on the handle. Is there a benefit to the spinning other than making it easier to go through the leather? Using the press like this is a game changer for me. I think I'll be able to get my stitch lines straighter and do it without damage to my body or upsetting anyone else with the noise. Working with heavy leather, I can probably go faster too vs hammer the 6 prong punch 4-5 times to get it through. Maybe I'll invest in a dedicated press eventually, but for now I can use this and get good results. I'm not sure if the drill chuck's ability to spin with the punch in it is a good or bad thing for this yet.

Many thanks to all respondents! Very helpful! When I get the appropriate appliance, (and some practice!!) I'll share what I am making!

WOW! That is some awesome work. Very talented. I'm still new at this so thanks very much for your help. I really do appreciate it. Happy carving

Here is a small set of single hole punches that are made for the drill press. I used to have a customer that I made leashes for and each required 8 holes punched into 10/12 Latigo. They saved my life and sanity. https://www.harborfreight.com/6-piece-hollow-punch-set-67030.html

I made a couple hundred probably. Some stock and some custom. My favorites (and most popular) were made from heavy chrome tan and then tooled side panels. The veg tan were harder to clean and tended to roll a bit over time. These chrome tan could roll up in a drawer for storage and lay right out flat. Handy for the folks with living quarter horse trailers. Heavy chrome tan and tooled strips. I treated them with at least three coats of acrylic finish and they wiped off well with minimal staining. I treated vegtan coasters the same.

Using LW's search for "drill press" AND stitching brought up lots of hits, most not fitting what we want. Down 20 or 30 items, found a good hit. Better to try a google search like this site: leatherworker.net "drill press" sewing stitching -machine -motor Site: tells google to search the listed site "drill press" quotes tell google to include both words, not individual -machine tells google to ignore machine The google search engines are much faster and easier to select the parameters you want and don't want. Add or remove additional parameters as you like.

A bit different but - First tip I EVER learned on the internet was from the old IILG group and Verlane Desgrange. (fun factoid - this group morphed out of the IILG - courtesy of a leather artist from Africa and a pizza baking momma from Ohio @Johanna). Verlane posted about chucking your mini or maxi punches in the drill press and turn it on. I literally read that, walked straight out to the shop and tried it. You want to make punching holes easy and no effort to remove? Even on damp sticky skirting with a big tube punch? This is it. That single tip was worth my annual dues right there. If you have visited the shop, I expect Rundi has demonstrated punching round holes with a drill press and using a rein trimmer to cut pieces. NOTE - As the punch tubes fill up the punchings will will fly out the ejection port in random directions. Eye protection is recommended.

There have been many threads about this subject over the years. Some ppl use a drill press, some use an arbour press and I use a Tandy Pro-Press

I use my drill press for my maker's stamps and other large stamps. Using it for punches is a good idea. I've thought about putting hole punches in it but haven't as of yet. Looks like it's a good use for your purposes. Good thinking.

Yes, but didn't see anything. Maybe I didn't look hard enough or maybe this is the first post on the topic?

This option is so the motor can be mounted left or right or some other permutation depending on how it is belted, whether the motor is on the left side of the drive belt or right side. If you turn a sewing machine backwards, the hook can't pick up the top thread, and you will likely get into quite a mess. Reverse lever on a sewing machine reverses the action of the feed dog and walking feet, not the hook action.

12. I'm looking at the Consew 29B. Prefer the larger bobbin. I'm pretty confident that I know what machine I need, more just curious about my original questions. I mostly just want to make sure that the Consew machine is going to be a significant improvement over the replica version.

Have you done a search here to see what has been posted? You could search for drill press and related keywords.

The next question is do you need a 12" or 18" arm? kgg

No, I'm definitely in need of a patcher. I customize and repair sneakers.

First off what are you needing / wanting to sew as there maybe better options then a patcher? kgg

I'm sure someone else has already thought of this and it might have been posted already. I put a six prong hole punch into my drill press and it works really well. I was considering buying a press so I could avoid waking up the neighbors and the jarring to my hands/arm from hammering. Some of my mistakes on my first project were a result of shifting the punch ever so slightly as I pulled the hammer back to hit. I think this is an approach that will help me and maybe some others.

Hello everyone. I was wondering if anyone has made any placemats. My daughter asked about them and I have no idea the type of leather to use and how to finish it. She would like it at least stamped on the edges if hand carving can't be done. Any suggestions would be greatly appreciated. Thanks

that's good! Just wanted to check that the middle foot had not been disconnected from the driving apparati. Here's what I would check, in this order. Page 13, "Reengage safety clutch". It's typical when the bobbin binds up for the safety clutch to trip. Make sure it's reengaged. Page 13 "Reverse Feed Mechanism". You mentioned a screw came off. I would inspect the reverse feed to make sure all the parts are in place and moving properly. Page 26, "Replacement of Arm Shaft Connection Belt". You don't need to remove the belt, but follow the instructions for verifying that the arm shaft (the one that the hand wheel bolts to) is in time with the hook shaft. Page 24, "Feed Eccentric Adjustment". You need to get the feed dog so that it halfway through it's fore-aft stroke when the needle is at bottom dead center. Page 23 and 24, "Feed Dog Adjustment". You want the feed dog to be at its highest point when the needle is at bottom dead center Page 25, "Lifting Eccentric and Alternating Presser Feet".