Northmount Posted February 3, 2024 Report Posted February 3, 2024 On 1/31/2024 at 7:41 AM, MikeLB said: Uhoh, rookie here, why a servo motor? Will the standard delivered work well? Can y'all suggest a good place to begin? Good book? Good tutorial site? I am planning on covering the seats on my BMW Z4, wish me luck, Mike Have you had a read through this thread? You can search for servo motors and find lots of information in many threads. Basically, a servo motor has variable speed and only runs while sewing. A clutch motor runs all the time and you have to learn to feather the clutch to make the machine run slow. It is even more sensitive than a clutch on a car with a standard transmission. It goes from 0 to 60 in a split second. Quote
Members DanaStanley Posted February 3, 2024 Author Members Report Posted February 3, 2024 (edited) 12 hours ago, MikeLB said: anybody? It will do upholstery just fine without a servo motor, just break it in good like they tell you to do. I returned mine to original and put the servo on a Juki DDL8700 H. Edited February 3, 2024 by DanaStanley Quote
Members MikeLB Posted February 10, 2024 Members Report Posted February 10, 2024 Thank You'se so much. Quote
Members Nadiri Posted April 6, 2024 Members Report Posted April 6, 2024 I see a lot of post about swapping out clutch for servo motors or installing servo motors to machines that are being inserted/installed into tables. Is there any way for me to slow down my consew CP206RL by just replacing the wheel with a larger one and getting an appropriately sized belt? I'm hoping to keep it portable...maybe. Quote
Members DanaStanley Posted April 7, 2024 Author Members Report Posted April 7, 2024 (edited) On 4/6/2024 at 10:42 AM, Nadiri said: I see a lot of post about swapping out clutch for servo motors or installing servo motors to machines that are being inserted/installed into tables. Is there any way for me to slow down my consew CP206RL by just replacing the wheel with a larger one and getting an appropriately sized belt? I'm hoping to keep it portable...maybe. Yest there is the kit that fits Sailrite fits this! Its wheels and a belt. Contact Us (sailrite.com) Maybe this Speed Reduction Pulley for Ultrafeed® & Leatherwork® (sailrite.com) Edited April 7, 2024 by DanaStanley Quote
Members Dominique Posted August 10, 2024 Members Report Posted August 10, 2024 Did anyone change the foot on theirs? I just got one of these and been practicing on scraps and notice that the foot texture is causing the leather to have indentation and rubbing off the dye on embossed leathers. Is there a smooth walking foot? Quote
Moderator Wizcrafts Posted August 10, 2024 Moderator Report Posted August 10, 2024 39 minutes ago, Dominique said: Did anyone change the foot on theirs? I just got one of these and been practicing on scraps and notice that the foot texture is causing the leather to have indentation and rubbing off the dye on embossed leathers. Is there a smooth walking foot? Sailrite does offer smooth and a knurled foot set for their leather sewing machine variant. The pebble grain pattern is a little friendlier to veg-tan ;leather than the stock feet, which have angled teeth. The totally smooth set will have less pull on the top layer and could slip instead of feeding slick material. Quote Posted IMHO, by Wiz My current crop of sewing machines: Cowboy CB4500, Singer 107w3, Singer 139w109, Singer 168G101, Singer 29k71, Singer 31-15, Singer 111w103, Singer 211G156, Adler 30-7 on power stand, Techsew 2700, Fortuna power skiver and a Pfaff 4 thread 2 needle serger.
Members Dominique Posted August 15, 2024 Members Report Posted August 15, 2024 @Wizcraftsthank you! Quote
CdK Posted August 16, 2024 Report Posted August 16, 2024 (edited) On 4/6/2024 at 8:42 AM, Nadiri said: I see a lot of post about swapping out clutch for servo motors or installing servo motors to machines that are being inserted/installed into tables. Is there any way for me to slow down my consew CP206RL by just replacing the wheel with a larger one and getting an appropriately sized belt? I'm hoping to keep it portable...maybe. @Nadiri I added the WorkerB package from Sailrite to my machine to improve the speed control & torque and keep it portable. I have also added feed dogs and presser feet better suited for leather work along with a stitch length plate. Member kgg here sells a nice kit for this. My starting point was a cheap generic base machine that turned into something useable. In this journey I spent considerable time and a lot of money to get it to where it is now reliable and with utility. Not recommended for those not mechanically inclined and not prepared to learn how to tune this machine. Edited March 24 by Northmount Duplicates Quote Leather work machines I own: Thor 1341, Thor 441, LSZ-1 clone, 801 bell skiver, Tinker's Delight Shoe Patcher. (Tippmann Boss was re-homed.)
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.