Nothing new but

[Frodo]

[Frodo]

The letter I. Makes a nice border stamp

 

[Frodo]

On 5/31/2023 at 7:48 AM, chuck123wapati said:

yea I think i posted this.

Still have not achieved the 3 D look that you did.  But while trying to pull it off I came across something rather interesting 

but,  I need you to pick up where I am leaving off and take it all the way 

I made a double using c-830 and c-429

can you try and make both designs 3-D?

I think it will be rather bad ass

 

 

[Frodo]

Rifle sling I am working on using that design. 

[chuck123wapati]

On 10/27/2023 at 12:34 AM, Frodo said:

Rifle sling I am working on using that design. 

i think i can see what you are getting at, I'll give her a go.

 

[Frodo]

Cool.  It is a challenge for sure 

[Frodo]

On 11/28/2023 at 8:10 AM, chuck123wapati said:

i think i can see what you are getting at, I'll give her a go.

 

Yeah.  I see 2 lines crossing back and forth over eAch other,  but I just can not seem to bring out the 3 d effect that you are good at

[chuck123wapati]

On 12/2/2023 at 8:32 AM, Frodo said:

Yeah.  I see 2 lines crossing back and forth over eAch other,  but I just can not seem to bring out the 3 d effect that you are good at

here ya go sorry for taking so long to respond. Here is the basic pattern i used a camo tool 431 if i remember right. and a 701 shaded beveller. the space between the two camo lines is approximately 1/8". The beveller is used to extend the one curve line to appear its going over the other curve. It doesn't take much to create the effect. I use hand pressure to set the bevel stamp. do one side then turn your piece over and do the other exactly the same.

 

 

[chuck123wapati]

6 minutes ago, chuck123wapati said:

here ya go sorry for taking so long to respond. Here is the basic pattern i used a camo tool 431 if i remember right. and a 701 shaded beveller. the space between the two camo lines is approximately 1/8". The beveller is used to extend the one curve line to appear its going over the other curve. It doesn't take much to create the effect. I use hand pressure to set the bevel stamp. do one side then turn your piece over and do the other exactly the same.

 

 

 

[Frodo]

Wow, thanks,  that is kinda freaky looking

 

[Frodo]

Got a job for you

If you want it. Tell me how much and I will send it along with the knife 

remove the scales and replace with a hardwood. Walnut if you have it if not what ever is around

 

[chuck123wapati]

2 hours ago, Frodo said:

Got a job for you

If you want it. Tell me how much and I will send it along with the knife 

remove the scales and replace with a hardwood. Walnut if you have it if not what ever is around

 

I have some antler. 

[Frodo]

That’s even better

[Frodo]

On 12/13/2023 at 8:01 AM, chuck123wapati said:

I have some antler. 

He backed out

a rivet setting tool for a stamp

[chuck123wapati]

cool idea with the stamps  if you meant I backed out I sent a pm to you.

[Frodo]

1 hour ago, chuck123wapati said:

cool idea with the stamps  if you meant I backed out I sent a pm to you.

No!!!   Not you,   Guy who wanted the handle backed out

[MarshalWill]

3 hours ago, Frodo said:

 

a rivet setting tool for a stamp

 

What rivet setting tool is that? It makes a great stamp.

[chuck123wapati]

57 minutes ago, Frodo said:

No!!!   Not you,   Guy who wanted the handle backed out

[Frodo]

51 minutes ago, MarshalWill said:

What rivet setting tool is that? It makes a great stamp.

It is a tubular peening tool

[MarshalWill]

2 hours ago, Frodo said:

It is a tubular peening tool

Thanks. It looks good.