Manual Strap Cutter Machine: Opinions/Recommendations

[DieselTech]

Guys & gals I would like to buy a strap cutting machine. 

Just curious if any of you have seen or used the TandyPro manual strap cutter. 

I'm curious if I can get by with it for a few years. 

Or is it junk?

Is there a better china/import brand option out there? 

Thanks. Any & all help will be greatly appreciated. 

[DieselTech]

Well I just said "F" it & bought 1 of these strap cutters. I will let you know what I think of it in a few days if I get around to it. 

Lmao I got a Cobra 26 to assemble too. 

[Ingenero]

I'll be interested to hear your experience...I'm unlikely to buy one any time soon, but am curious how well it works.  I did initially look for cheaper Chinese options, but didn't see anything comparable - they were all far more manual.

[DieselTech]

5 hours ago, Ingenero said:

I'll be interested to hear your experience...I'm unlikely to buy one any time soon, but am curious how well it works.  I did initially look for cheaper Chinese options, but didn't see anything comparable - they were all far more manual.

As soon as I get around to installing the cutters blades. I will report back with my thoughts. I did watch this guy cut saddle skirting with it & I know it wasn't designed for that. But it did cut the 14-16oz leather saddle skirting.  

[THein]

Sorry I didn't have the opportunity to respond to the first post but likely it's a good machine.  I bought a strap cutter from Weaver's years back and resembles yours a lot.  I'm more than happy with it.  Takes some getting used to if you want to split directly from a side. Best bet is to hand cut a wee bit more than you need from the side and then run it through.  A little waste but you've no "wonky" straps!

Edited October 4, 2024 by THein

[DieselTech]

2 hours ago, THein said:

Sorry I didn't have the opportunity to respond to the first post but likely it's a good machine.  I bought a strap cutter from Weaver's years back and resembles yours a lot.  I'm more than happy with it.  Takes some getting used to if you want to split directly from a side. Best bet is to hand cut a wee bit more than you need from the side and then run it through.  A little waste but you've no "wonky" straps!

Thanks. Yeah I was going to hand cut a 10-12" wide strip out of the side of leather.

Then run it thru the strap cutter for whatever given width I need. 

[RockyAussie]

On 9/21/2024 at 9:04 AM, DieselTech said:

As soon as I get around to installing the cutters blades. I will report back with my thoughts. I did watch this guy cut saddle skirting with it & I know it wasn't designed for that. But it did cut the 14-16oz leather saddle skirting.  

I would just check that the gears are not plastic ones as I have seen some models have them and do not last long cutting thicker than recommended.

 

[RockyAussie]

26 minutes ago, DieselTech said:

Thanks. Yeah I was going to hand cut a 10-12" wide strip out of the side of leather.

Then run it thru the strap cutter for whatever given width I need. 

This video I did a little while ago could help you on this - https://youtu.be/Q3cVOtCNjEg?si=xrCJA5Rep8YEl89Y

Edited October 5, 2024 by RockyAussie

[DieselTech]

37 minutes ago, RockyAussie said:

This video I did a little while ago could help you on this - https://youtu.be/Q3cVOtCNjEg?si=xrCJA5Rep8YEl89Y

Thanks. I appreciate it. I watched that video here recently. Then went to a metal fab shop & purchased a 8ft section of 1½" stainless steel flat strap. 

[DieselTech]

Ok guys & gals, I finally got around to testing the TandyPro manual rotary strap cutter. 

It is definitely a keeper. This cutter is nice. If you set it up, according to the manual. 

Here is some 10-12oz Hermann oak latigo. Cut it like butter. Awesome!!!

Decided to really test the machine out. This is 14-16oz Hermann oak saddle skirting. Cut it like butter! Awesome machine for the money.