Contributing Member JLSleather Posted February 3, 2017 Author Contributing Member Report Posted February 3, 2017 Oh, and by "basic version" I mean this : Quote "Observation is 9/10 of the law." IF what you do is something that ANYBODY can do, then don't be surprised when ANYBODY does.
Contributing Member JLSleather Posted February 11, 2017 Author Contributing Member Report Posted February 11, 2017 (edited) I was fixinta upload another holster pattern er two afore the lights go out around here (moving truck here in the morning). But...not sure my wife is on board with that Wait.. ya know--- she ainta bossa me! XDs pattern uploaded shortly Okay, there ya go! Edited February 11, 2017 by JLSleather Quote "Observation is 9/10 of the law." IF what you do is something that ANYBODY can do, then don't be surprised when ANYBODY does.
Members PeashooterJoe Posted February 25, 2017 Members Report Posted February 25, 2017 Thanks for the Patterns. PeashooterJoe Quote
Contributing Member JLSleather Posted February 25, 2017 Author Contributing Member Report Posted February 25, 2017 37 minutes ago, PeashooterJoe said: Thanks for the Patterns. PeashooterJoe Welcome -- thanks for puttin' em ta use! Quote "Observation is 9/10 of the law." IF what you do is something that ANYBODY can do, then don't be surprised when ANYBODY does.
alpha2 Posted February 25, 2017 Report Posted February 25, 2017 Well, here's my first attempt at a pancake holster from one of JLS' patterns. A lot of learnin' went into this one! If I do another with the reinforcement, I'll skive it down or use thinner leather. And, I won't forget to edge finish the reinforcement panel before I stitch it to the front. And I'll use thinner thread. And I'll use better leather. And I'll clean the leather before I stain it. And I'll move the slot stitching out a bit more, as my plan is to use a thick gunbelt I'm just finishing up right now, and the slots could be a it wider. And I won't pull out a lot of the antiqueing with the first coat of finish on the reinforcement. But, hey! The pattern worked just fine! Thanks!!! Jeff Quote So much leather...so little time.
bikermutt07 Posted February 26, 2017 Report Posted February 26, 2017 6 hours ago, alpha2 said: Well, here's my first attempt at a pancake holster from one of JLS' patterns. A lot of learnin' went into this one! If I do another with the reinforcement, I'll skive it down or use thinner leather. And, I won't forget to edge finish the reinforcement panel before I stitch it to the front. And I'll use thinner thread. And I'll use better leather. And I'll clean the leather before I stain it. And I'll move the slot stitching out a bit more, as my plan is to use a thick gunbelt I'm just finishing up right now, and the slots could be a it wider. And I won't pull out a lot of the antiqueing with the first coat of finish on the reinforcement. But, hey! The pattern worked just fine! Thanks!!! Jeff Well, is there anything you like about it??? Lol I think it was a great attempt. Quote I'm not paying 80 bucks for a belt!!! It's a strip of leather. How hard could it be? 4 years and 3 grand later.... I have a belt I can finally live with. Stitching is like gravy, it's only great if you make it every day. From Texas but in Bossier City, Louisiana.
alpha2 Posted February 26, 2017 Report Posted February 26, 2017 I know. I'm awfully hard on myself. Or so says my trophy wife! It's just that my last holster was so much better, I feel like I'm backsliding bigtime. But like I said, I learned a lot! So it was a roaring success. Quote So much leather...so little time.
Contributing Member JLSleather Posted February 26, 2017 Author Contributing Member Report Posted February 26, 2017 Well, I don't think it's 'so bad'. I'm not a fan of basket weave (i think it's way over done) but the color works. When I posted those patterns, I wanted them to be useable as-is -- but i never intended for everybody to make them 'just like that'. Idea is, a new guy can make that holster and gain some experience. And the next guy can use that design as a starting point to make his own design. Just FYI -- a 1/4" thick belt works in a 1/4" wide slot just fine How does the end look? In the pic, it looks like the pistol could have seated a bit deeper (to teh stitch line under it).. maybe the stagger in the stitch line was just a tad early? Quote "Observation is 9/10 of the law." IF what you do is something that ANYBODY can do, then don't be surprised when ANYBODY does.
Members Mattsbagger Posted February 26, 2017 Members Report Posted February 26, 2017 I butchered up your Shield pattern Jeff.lol People seem to like the way it wears and carries. I know I do. Quote
Members Mattsbagger Posted February 26, 2017 Members Report Posted February 26, 2017 17 hours ago, alpha2 said: Well, here's my first attempt at a pancake holster from one of JLS' patterns. A lot of learnin' went into this one! If I do another with the reinforcement, I'll skive it down or use thinner leather. And, I won't forget to edge finish the reinforcement panel before I stitch it to the front. And I'll use thinner thread. And I'll use better leather. And I'll clean the leather before I stain it. And I'll move the slot stitching out a bit more, as my plan is to use a thick gunbelt I'm just finishing up right now, and the slots could be a it wider. And I won't pull out a lot of the antiqueing with the first coat of finish on the reinforcement. But, hey! The pattern worked just fine! Thanks!!! Jeff Better than my first go. I don't like stitching around the slots. Personal preference. If you punch at 1.5 slot and edge and burnish a 1.5 gun belt fits just fine. Good hand stitching is done by doing it a lot marking stitching line and stitching holes marked. Quote
Contributing Member JLSleather Posted February 26, 2017 Author Contributing Member Report Posted February 26, 2017 Well, long as we're commenting (crap, I aint gonna git nuthin done taday )... 16 minutes ago, Mattsbagger said: I butchered up your Shield pattern Jeff.lol People seem to like the way it wears and carries. I know I do. I don't call that butchered.. I'd call that 'amended' -- looks good! 17 hours ago, alpha2 said: A lot of learnin' went into this one! If I do another with the reinforcement, I'll skive it down or use thinner leather. I'm actually not a fan of a "reinforcement panel" on teh front of a 50/50 pancake (it's not doing nearly as much "reinforcing" as people say, unless it wraps around). Still, a guy could do some basket stamp without the panel. This one is stitched at the top and bottom because it's lined (with natural goat). The stamp is used INSTEAD OF teh panel. Quote "Observation is 9/10 of the law." IF what you do is something that ANYBODY can do, then don't be surprised when ANYBODY does.
Boriqua Posted February 26, 2017 Report Posted February 26, 2017 18 hours ago, alpha2 said: Well, here's my first attempt at a pancake holster from one of JLS' patterns. A lot of learnin' went into this one! If I do another with the reinforcement, I'll skive it down or use thinner leather. And, I won't forget to edge finish the reinforcement panel before I stitch it to the front. And I'll use thinner thread. And I'll use better leather. And I'll clean the leather before I stain it. And I'll move the slot stitching out a bit more, as my plan is to use a thick gunbelt I'm just finishing up right now, and the slots could be a it wider. And I won't pull out a lot of the antiqueing with the first coat of finish on the reinforcement. But, hey! The pattern worked just fine! Thanks!!! Jeff I think it looks fine. Most especially for a first attempt but having those known working patterns sure help to get you a good looking working product!! I wish there was a thread like this when I started!! The thread doesn't seem to heavy aesthetically to me. Was it just difficult to work with? What size was it? I like Jeff's slot reinforcement technique and while I sometimes mess with the shape of it I think it is engineered well and works and is more pleasing to the eye. I would go back to that and leave off the stitching around the belt slots. All your other stitching looks good though. While I agree the Reenforcement panel does little to reinforce what it does do nicely is hold a stamp. I have found that since it is an extra piece that isnt as affected as the body when wetmolding that the stamps in the reinforcement hold up deeper than when done on the body. I do it both ways depending on my mood but either your leather wasnt cased well when you did the baskeweave or you didnt hit that tool hard enough. Give it a good WHACK on well cased leather and the basketweave will stand out more. Nice job .. imagine what your 10th one will look like!! Quote
alpha2 Posted February 26, 2017 Report Posted February 26, 2017 (edited) Thanks for the tips, guys! The thread was the first braided cord I've used. It was a bear with the awl I had available. A lot of plier usage on the thick leather. I imagine a larger awl and needle would have helped a lot. Edited February 26, 2017 by alpha2 Quote So much leather...so little time.
Contributing Member JLSleather Posted March 12, 2017 Author Contributing Member Report Posted March 12, 2017 Swing anna miss.. not quite what I was aiming for. Still, it'sa 8 outta 10, so just a couple tweaks to go .. Used this W/C skirting, since for some reason it isn't 'hardening' like W/C normally would --- so putting it to use here! Quote "Observation is 9/10 of the law." IF what you do is something that ANYBODY can do, then don't be surprised when ANYBODY does.
Members OLDNSLOW Posted March 12, 2017 Members Report Posted March 12, 2017 that there one a full size p320? Quote
Contributing Member JLSleather Posted March 12, 2017 Author Contributing Member Report Posted March 12, 2017 It almost was Swing anna miss.. not quite what I was aiming for. Still, it'sa 8 outta 10, so just a couple tweaks to go . Quote "Observation is 9/10 of the law." IF what you do is something that ANYBODY can do, then don't be surprised when ANYBODY does.
Members OmnipotentOtter Posted March 14, 2017 Members Report Posted March 14, 2017 Just wanted to say thanks for making these patterns and instructions available. I just finished my first attempt at a holster (1911 Avenger style) and while it doesn't hold a candle to the items you guys are putting out I'm actually pretty happy with it given my total lack of experience. I tried to attach a pic but can't get the file size right, so if you want a laugh at how a total newbie does things here's the whole process that I went though to make it (including final product pic): Would certainly welcome any feedback/advice/critiques - I learned a ton on this first go round but obviously still have a long way to go! Thanks again for sharing your knowledge! Quote
Members Mattsbagger Posted March 15, 2017 Members Report Posted March 15, 2017 14 hours ago, OmnipotentOtter said: Just wanted to say thanks for making these patterns and instructions available. I just finished my first attempt at a holster (1911 Avenger style) and while it doesn't hold a candle to the items you guys are putting out I'm actually pretty happy with it given my total lack of experience. I tried to attach a pic but can't get the file size right, so if you want a laugh at how a total newbie does things here's the whole process that I went though to make it (including final product pic): Would certainly welcome any feedback/advice/critiques - I learned a ton on this first go round but obviously still have a long way to go! Thanks again for sharing your knowledge! Looks good for a first go. I started out using Edge Kote but changed to dying my edges. Practice your stitching and edging on the small wallets that Jeff has on his site with his holsters. They use minimum amount of leather and help nail down the techniques. He also is a font of information and advise. Keep on keeping on. Ta. Matt. Quote
Contributing Member JLSleather Posted March 15, 2017 Author Contributing Member Report Posted March 15, 2017 If you're using contrasting thread, it's easier to dye the part under the belt loop before sewing on the panel. And you'll likely find it faster and easier to pick up some type of punch for the slot rather than drilling. Some use an oblong punch, some use a round punch for each end and a knife of some sort between. Quote "Observation is 9/10 of the law." IF what you do is something that ANYBODY can do, then don't be surprised when ANYBODY does.
Members OmnipotentOtter Posted March 15, 2017 Members Report Posted March 15, 2017 Thanks for the feedback and advice guys! This was my first go with Edge Kote and think it did a decent job of at least imparting some consistency in the color for the edges. I do have a set of punches that I can next time, they are "pin punches" but likely will work for this. I didn't use them on this project because I was lazy - they were buried in the garage. But I've dug them out now and should be able to just use a couple of 2x4s to support the leather but not the impending hole. I was also a little worried about whether the punches would tear the leather or somehow mar it - but in reality using the standard drill bits really did that more than a punch will (I think). The dye job is another "opportunity for improvement" next time - it definitely would have been better to dye all of it before stitching on the reinforcement panel - but that's assuming I would have thought that far in advance. This has (and continues to be) a learning experience! Quote
Contributing Member JLSleather Posted March 15, 2017 Author Contributing Member Report Posted March 15, 2017 Pin punches are great for replacing shear pins, but not so good on leather You'll want a set of hollow HOLE punches.. much better for leather. I'm not recommending any particular brand, but this one will show you the idea. Something in about a size 6 or 7 should be fine. https://www.tandyleather.com/en/product/craftool-round-drive-punches Quote "Observation is 9/10 of the law." IF what you do is something that ANYBODY can do, then don't be surprised when ANYBODY does.
Members Mattsbagger Posted March 15, 2017 Members Report Posted March 15, 2017 (edited) 2 hours ago, OmnipotentOtter said: Thanks for the feedback and advice guys! This was my first go with Edge Kote and think it did a decent job of at least imparting some consistency in the color for the edges. I do have a set of punches that I can next time, they are "pin punches" but likely will work for this. I didn't use them on this project because I was lazy - they were buried in the garage. But I've dug them out now and should be able to just use a couple of 2x4s to support the leather but not the impending hole. I was also a little worried about whether the punches would tear the leather or somehow mar it - but in reality using the standard drill bits really did that more than a punch will (I think). The dye job is another "opportunity for improvement" next time - it definitely would have been better to dye all of it before stitching on the reinforcement panel - but that's assuming I would have thought that far in advance. This has (and continues to be) a learning experience! The reason I quit use in Edge Kote is it can scratch off. YMMV. You can get hole punches and wood chisels at Harbor Freight to do belt slots also. Edited March 15, 2017 by Mattsbagger Quote
Members OmnipotentOtter Posted March 17, 2017 Members Report Posted March 17, 2017 On 3/15/2017 at 2:33 PM, JLSleather said: Pin punches are great for replacing shear pins, but not so good on leather You'll want a set of hollow HOLE punches.. much better for leather. I'm not recommending any particular brand, but this one will show you the idea. Something in about a size 6 or 7 should be fine. https://www.tandyleather.com/en/product/craftool-round-drive-punches The learning continues. Thanks for correcting me on that before I ruined holster #2; I'll make sure I get the right tool for the job. I really do appreciate everyone's willingness to help a newbie like me out - this is really a fantastic community and I'm very glad I found it! Quote
Members longun45 Posted March 18, 2017 Members Report Posted March 18, 2017 (edited) Some of what I have been doing. Learning a bunch along the way. I know some of this stuff is not a pretty as I would like, but I have only been doing this for a short while. This is the colt auto pattern I made this pattern off another and kind of bent it a bit, this is the first of and I think it came out ok. Still learning about the sewing machine and what it will and won't do and figuring workarounds. This came out alright except for the one dropped stitch When wet molding it that reinforcement panel is a bugger to bend. I am working on those molding skills. I got a wild hair on this one and wondered what would happen IF. SO I wet rolled the upper edge and formed it around the gun. No great works of art here yet, but they are coming. Many thanks to JLS for the patterns and the inspiration. Edited March 18, 2017 by longun45 Photos and comments Quote
Contributing Member JLSleather Posted March 18, 2017 Author Contributing Member Report Posted March 18, 2017 Looks like some good practice ta me -- and the shield looks good! Quote "Observation is 9/10 of the law." IF what you do is something that ANYBODY can do, then don't be surprised when ANYBODY does.
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.