The "best" Contact Cement?

[dfrensdorff]

Hello All....I am sure this question has been asked and answered many times,, but a search came up somewhat empty.....what is the best contact cement you can buy? I am currently using Weldwood Red label, and for the most part it works just fine....with the exception on a belt where I used a light Horween horsefront glued and then sewn as a lining with a buffalo belt. It is separating just a bit at the buckle holes.......Maybe this is what will happen with any glue but just checking to see if there is a drop dead "best" contact cement....Thanks.........Don

[Chief31794]

I've used Master's Contact Cement for years, it works so I use it. You'll probably get lots of opinions on which is best, try a small can of Barge, Masters, Weldwood and decide for yourself. Mine works so I have no desire to look for anything else.

Chief

[electrathon]

Renia in a green can. Best and strongest there is. Masters was Renia, relabeled, till recently. Also does not have toluene in it, far less health risks than Barge. It is not the cheapest.

[dfrensdorff]

Thanks gentlemen for the information.......

Edited October 12, 2015 by dfrensdorff

[Colt W Knight]

I use the red label Weldwood. I haven't had any reason to stop using it.

Edited October 13, 2015 by Colt W Knight

[24VOLTS]

I don't like Barge. Make fell bad.

I have recently purchased Aquilim 315 from Lisa Sorrell.

I like the stuff. No smell and it seems to be strong.

I bought the orange brush and that seems to work good.

[24VOLTS]

What is the difference between the red and green can of weldwood?

I have used the green can. It seems that it starts to set up in the glue pat and then hardens.

It seems like I am prying dried glue out of the pot every 4-5 weeks.

[electrathon]

I don't like Barge. Make fell bad.

I have recently purchased Aquilim 315 from Lisa Sorrell.

I like the stuff. No smell and it seems to be strong.

I bought the orange brush and that seems to work good.

Aquilim is a Renia product. It is a great water based adhesive.

[Art]

I don't like Barge. Make fell bad.

I have recently purchased Aquilim 315 from Lisa Sorrell.

I like the stuff. No smell and it seems to be strong.

I bought the orange brush and that seems to work good.

Aquilim is a Renia product. It is a great water based adhesive.

I've found (through conversation) that the Aquilim takes a little longer to dry, like 2x.

On another topic, who sells Flexofil, Stopgap, or other cork bottom filler here in the States?

Art

[earlthegoat2]

I know there are flammable and non flammable varieties of Weldwood. That is one difference in can color.

I have tried: Masters, Weldwood (flammable),Old Barge, New Barge, Old Tandy, New Tandy, 3M Scotchweld 4475,

The one that worked to my satisfaction was the Old Tandy and Old Barge. The others just work. They work but not like the old ones. The old ones made a permanent bond the second they touched each other. The new ones can be worked around a little. This can be a good thing but I like the confidence that comes with the old style adhesion.

I use Masters and occasionally 3M Scotchweld now. The 4475 variety is their product for leather. The Scotchweld line are known as "Plastic Adhesives". Another general note: If it says not for sale in California, then it will work about as good as anything that is available. The 4475 carries that label. It gives new meaning to the term expensive. It costs 20 dollars for 5oz. I only use it sparingly where not a lot of flex will be needed in the finished product. I have no doubt it would work for those areas though.

Im going to try Pliobond next. They have a specific product for porous surfaces.

Edited November 22, 2015 by earlthegoat2